The rectangular gate shown in Fig. Q.B1 is 2 m wide (perpendicular to the paper and is hinged about its upper edge B. The gate divides a salt-water (density 1030 kg/m³) tidal basin on the left from a channel on the right. Calculate the torque M on the shaft of the gate at B required to prevent the gate from opening when the channel on the right is empty as shown.

Q: Draw the bending moment diagram of the system under the influence of external loads below. Calculate…

A: (a) Draw the bending moment diagram of the system under the influence of external loads below. (b)…

Q: he resultant of the force system shown is a force-couple R and ?? acting at point O. Determine the…

A: Question is based on a force system . Loading condition on system and dimension of member are given…

Q: 1.5 m 0.3 m 15 kg A Compressed by 25 mm k = 300000 N/m

A:

Q: A plane rectangular gate (width 5 m) is hinged at the support at B as shown in Figure 2. Neglect the…

A: For minimum for P reaction at A will be zero.

Q: Determine the moment of the distributed loading at point B.

A:

Q: A 200-mm-diameter pulley is prevented from rotating relative to 60-mm- diameter shaft by a…

A: Torque is simply the amount a golf shaft twists when subjected to a known amount of force and the…

Q: The thin-walled single cell beam shown in figure has been idealized into a combination of direct…

A: To determine the location of the shear center for vertical shear loading, we can use the principle…

Q: Question 8 A three hinged arch is 6 m high and 18 m long. The supports are at same level. Arch is…

A: Given- Height h=6 mLength L=18 mLoading as shown in the figure It is needed to find the ratio of…

Q: The section of a gate at the end of a tank is shown below. The length of the gate is 3 m  normal to…

A:

Q: For structural elements (beams and gantries) shown in the Figure, determine the internal efforts…

A: To find internal loading at point C

Q: mis A circular gate of radius submerged in a liquid with its top edge flushed on the liquid surface.…

A:

Q: Question 1: (B): Replace the distributed loading by an equivalent resultant force and specify where…

A: The given figure is shown below:

Q: Determine all the reactions on the following beam. Use DOUBLE INTEGRATION METHOD. 720 N 480 N/m 2.4m…

A: To find the reaction at support B, we will assume support B as redundant. Then we will divide the…

Q: P. water surface 2.5 m 2.7 m y? = 5x (parabola

A:

Q: Q.2 The resultant of the force system shown in Figure (2) is a vertical force of 1250N. Determine…

A:

Q: A slender rod ACB of length 1.50 m and mass of 15.0 kg is pinned at point C, which is 0.30 m from…

A: We have to find the speed of center of gravity of the slender rod when the rod is vertical

Q: Part A : Replace the loading by a single resultant force and determine its magnitude Part B :…

A: The given figure is shown below:

Q: • Find: External reactions in x and y directions needed to hold fixed vane. F,+ • Solution: OTS =…

A:

Q: The ends of a 0.25kg rod AB are constrained to move along slots cut in a vertical plate as shown. A…

A: Mass of rod = 0.25 kg spring constant = 3 N/m θ= 45° To determine: angular velocity at position 2

Q: a) Draw the hydrostatic pressure distribution on the gate, b) calculate the resultant force acting…

A:

Q: Analyze the frame shown below 37.5 kN/m BA C 4 m 4 m 3 m El = constant

A:

Q: The section of a cast iron beam in the shape of an in the shape of an inverted semi- circular…

A: Area of the beam section is A A=π1302-12022+10×70×2=3925+1400=5325 mm2 Centroid of the beam section…

Q: The structure is loaded as shown in the figure. Determine the internal axial force, shear force and…

A: To Determine The internal axial force, shear force and bending moment at point C. The internal…

Q: 03: For the beam shown in Figure (3), given INA = 1. 106mm, calculate the transverse shearing stress…

A: Where,B = Overall width of I section of the beamD = Overall depth of I section of the beamb =…

Q: The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth of a…

A:

Q: 200 mm 30 mm -25 mm V В 250 mm 30 mm 125 mm If calculating the shear stress at point B, what is the…

A: Step 1

Q: A gusset plate for a bridge truss is shown in the figure. Determine the magnitude and direction of…

A:

Q: P 3m A 2 В 4m

A:

Q: The steel shaft shown in Fig. P-314 rotates at 4 Hz with 35 kW taken off at A, 20 kW removed at B,…

A:

Q: For the figure shown below: a. Calculate the magnitude, direction, and sense of the resultant force…

A:

Q: Problem 1 Detemine the location of the resultant of the given forces from point A as shown in Figure…

A: Given:- A system of forces acting as shown

Q: Determine the vertical distance of the center of gravity of the curved gate from the water surface…

A: step 1-

Q: 4. The cantilever beam AC in Fig. 4 is loaded by a pair of magnitudes of 4800 N m at the tip C and a…

A: Given data in question  UDL 600 N/m Concentrated moment 4800 Nm Span 4m To find out  SFD BMD

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.