Two steel ropes connected to each other at point C are loaded as shown in the figure. The maximum tensile forces of the ropes AC and BC are 18.4 Fand 12.6* F Newton, respectively. Find a/The maximum force P that can be applied to point C b/ Find the value of y angle between CB and CP AI B 4"a P.

Two steel ropes connected to each other at point C are loaded as shown in the figure. The maximum tensile forces of the ropes AC and BC are 18.4 Fand 12.6* F Newton, respectively. Find a/The maximum force P that can be applied to point C b/ Find the value of y angle between CB and CP AI B 4"a P.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A member is loaded with force system as shown in figure. Find the Moment about A, B, C, D and E Where F1= 90 N, F2 =55 N, F3 =40 N, F4 =35 N, Fs =70 N, AB =140 m, Point C is in the mid of AE, CD = 45m, AE =120 m. the angle e =30° F4 Fs E e D F3 F2
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ¢ = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb , what is the maximum weight Wmax of the crate that the system can support? What is the angle 0 required for D equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) vec ? Wmax, 0 = lb, degrees
The rod ABC having a constant AE is subjected to external forces at points B and C, as shown. What is the required value of the P so that the displacement of end C will be zero?
A 100N load is supported by a strong bar as shown in the figure. The tension in the cable is 200N. Compute the value of angle "A" in degrees. 10 m 200N 100N ZA ZB 10 m
5. A steel bar has dimension of 5 cm x 2.5 cm x 1.5 mm respectively. It is subjected 3 mutually perpendicular loads of 250 kN (Tensile), 2.5 MN (tensile), 3.5 MN (compressive) acting along length, breadth & thickness directions respectively. Find the change in volume. Take E as 200GPA & Poisson's ratio 0.25. Also find the change in Length, breadth & thickness.
A cable is connected to an L shaped arm OAB as shown. The magnitude off the tensile force on the cable is given as T = 2500 and angle between the segment AB of the L- shaped arm and cable = 91.229 degrees. ( use the vector approach ) A) determine the components of the tensile force on the cable which are parallel and perpendicular to segment AB of the L-shaped arm
Q.3) An airplane wing is supported by a truss structure as shown below. Three vertical forces are applied at points C, D, and E along the upper surface of the wing. Use the Method of Sections to find the force in members BC, CG, and GF. Indicate whether the member is in tension or compression. A I 8' 2500 lb 3000 lb 1500 lb H 8' 8' 8' B C -G- D E F 18'
The prismatic bar AC is supported by a hinge at C and cable ADB that runs through a frictionless pulley at D as shown in the figure. What is the tension in the cable if the bar weighs 5 Ib/ft? 3 ft 5 ft в 5 ft