Answered: Two steel plates of 8 x 200-mm…

Two steel plates of 8 x 200-mm rectangular cross section are welded to the W310 × 52 beam as shown. The shearing stress in the beam is not to exceed 110 MPa. W310 X 52 8 mm x 200 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.8.3P

See similar textbooks

Related questions

Q: What is the maximum span for a 7.5-inch thick post-tensioned concrete two-way flat plate? Answer…

A: To find the maximum span for a 7.5-inch thick post-tensioned concrete two-way flat plate

Q: Define the term Shear Centre for Open Thin-Walled Members?

A: The shear center is a point from which a concentrated load passes; then, there will be only bending…

Q: how is a foundation post proyected from the moisture in the concrete support

A: The way by which protection of foundation post is done from moisture in the concrete support.

Q: Describe about the Installation procedure of Excavation Bracing?

A: Deep excavations with vertical sides need lateral supports to prevent cave in of the soil and to…

Q: Given a concrete column with an eccentric axial load determine a. The Cross-Section properties of…

Q: The architects decides to put a shear wall in the middle of the building as shown. Given the…

Q: 4.8 Refer to the following table from ACI Code to determine the maximum spans or minimum thickness…

Q: What is the flexure formula and tell what the unknown letters represent?

A: Solution: The flexure formula basically gives the internal bending stresses caused by an external…

Q: Describe about the what is the Earthquake Forces and Gravity Retaining Walls?

A: - Forces which generates due to earthquake are known as earthquake forces. - types of earthquake…

Q: Discuss about the pre tensioning and post tensioning procedure in detail?

A: Prestressing is the method of compressing an element of concrete using steel wires or strands.

Q: Given a singly reinforced rectangular beam with fc'= 35MPA and fy = 345MPA What is the minimum steel…

A: Given: The values of stresses are,

Q: What is batter piles?

A: A batter pile is a pile driven at an inclination to vertical to provide resistance to horizontal…

Q: Draw One-way slab- 12 mm diam. main bars spaced @ 300 mm o.c. b/w with 10 mm diam. extra top…

Concept explainers

Applications of Concrete Framing Systems

A concrete frame is a structure formed by the interconnection of beams and columns to form a structural network. In simple terms, it is the basic skeletal structure of a building or any construction. The concrete framing structure is built on a concrete foundation that forms the base of the entire structure. The concrete frame system is built to support floors, roofs, walls, beams, rafters, joists, etc.

Question

What is the largest allowable vertical shear?

Two steel plates of 8 × 200-mm rectangular cross section are welded to the W310 × 52 beam as shown. The shearing
stress in the beam is not to exceed 110 MPa.
D--
8 mm x 200 mm
W310 X 52

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Moment of inertia

VIEW

Step 3: First Moment of area

VIEW

Step 4: Allowable shear force

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 26 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Applications of Concrete Framing Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.