Two sources of fine aggregate F1 & F2 were mixed with the proportion (1F1 : 2 F2) . The result of the mixture is a fine aggregate (F) of adjusted specific surface, which was mixed with a coarse aggregate (C) resulting from a mixture of two other sources of coarse aggregates C1 & C2 with a proportion of (3C1 : 5C2). Having the specific surface of each source of fine and coarse aggregates. Deterrmine the proportion of fine to coarse aggregate (F : C) in order to get a specific surface of the total mixture of four sources equal to 24 cm?. Given: F1 F2 Ci C2 76 84 Specific surface (cm?/g)

Two sources of fine aggregate F1 & F2 were mixed with the proportion (1F1 : 2 F2) . The result of the mixture is a fine aggregate (F) of adjusted specific surface, which was mixed with a coarse aggregate (C) resulting from a mixture of two other sources of coarse aggregates C1 & C2 with a proportion of (3C1 : 5C2). Having the specific surface of each source of fine and coarse aggregates. Deterrmine the proportion of fine to coarse aggregate (F : C) in order to get a specific surface of the total mixture of four sources equal to 24 cm?. Given: F1 F2 Ci C2 76 84 Specific surface (cm?/g)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If you don't no the solution please leave it. I want right solution according to the question
Please
The percentage of aggregates of fine-ness modulus 2.7 is to be mixed with coarse aggregate of fineness modulus 7 to have a FM of 5.5 would be combined
Coarse aggregate is placed in a rigid bucket and rodded with tamping rod. The volume of the bucket is 20,000 cm3 and the weight of the dry-rodded coarse aggregate is 400N. The bulk specific gravity of the aggregate is 2.69. Determine;a) the bulk unit weight of the aggregate, in kN/m3b) the percent voids between aggregate particle in the container aaaaaaaaaaaaaaa
Choose the correct answer 1) Which type of aggregates gives good stability? a. Round b. Flaky c. Angular 2) Select the correct statement. a-Reduce thickness is one of the reasons of stabilize b-When the quality increase, the thickness is reduce e-If the layer has a high K-value,above layer shall has smaller thickness d. All of the above 4. Which of the following grade of bitumen is harder? b. 60/70 a. 40/50 c. 80/100 d. Cubic 3. The surface of the pavement should be a. Smooth b. Rough c. Sufficient enough to resist skid d. All the above acceptable e. All of them d. All are equal 5) If the soil characteristics, as subgrade, % passing 0.075 mm sieve = 30, % passing 0.425 mm sieve = 55, % L.L = 42, % P.L = 33. The Group Index equal a. Zero b. 1.0 c. 1.5 d. 2.0 e. 2.5 6. Rapid curing cut back bitumen is produced by blending bitumen with... a. Kerosene b. Gasoline c. Diesel d. Emulsion c- #4 7. Asphalt binders become harder (more viscous) as their temperature decreases and less soft (less…
31
a. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values? b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch. Note: Please answer both a and b... Please answer the both questions.. I don't want single b answer.. thank you
Design a Mix for the following Data. Specified strength = (99.5) MPa, Required Slump = 80 mmMaximum size of aggregate = 25 mm, FM of fine aggregate = 2.40Grading of aggregate as satisfied by ASTM C33 (American Society for Testing and Materials)SSD specific gravity of fine and coarse aggregate = 2.75Rodded bulk density of coarse aggregate = 1600 kg/cubic mAbsorption Capacity of coarse aggregate = 0.9 %Absorption Capacity of fine aggregate = 0.5 %Moisture Content of fine and coarse aggregate = 2 %Exposure Conditions = Normal
24
It is more convenient to adopt totally saturation curing regime when the slump type of the mix is shear slump * True False The surface area of the aggregate has a good effect on the workability. Therefore, they have a linear correlation. * True False Other:
Use the following data:Oven Dry weight - 4.98 kgWeight under water - 3.02 kgSSD Weight - 5.07 kg1. Determine the apparent specific gravity of the coarse aggregates.2.Determine the bulk specific gravity SSD of the coarse aggregates3.Determine the bulk specific gravity (Dry) of the coarse aggregates4.
make up a computation