Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown in the figure.The diameter of rod (1) is 1.75 in. and the diameter of rod (2) is 2.50 in. Determine the normal stress in rod 1. Answer in ksi 15 kips () 30 kips 30 kips (2)
Q: 1. A steel rod (initial diameter: 3.2 mm, initial length: 42 mm) is extended by a uniaxial tensile…
A: Given: Steel rod diameter, D= 3.2 mm Tensile load, F = 4800 N'
Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.
A: Maximum axial force P that can be applied to the steel plate
Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…
A: Given Elongation of the bar between A dan C δtotal = 0.22 in Strain ε2…
Q: Two strips of metal are pinned together as shown with a rod 10 mm diameter. The ultimate shear…
A: Given: Diameter=10mm Therefore, =5mm Shear stress=60Mpa.
Q: One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of…
A:
Q: (TUATION 3: A vertical brass post is 3.75m long and has a diameter of 25 cm. If the brass post is to…
A:
Q: TUnOWng prUDIEms. A steel wire of diameter 1 mm can support a tension of 0.2 kN. Determine the…
A:
Q: A brass wire (E = 100 x 10° Nm2) which is 6.336 m long experienced an elongation of 1.21 mm by a…
A: Given, Young's modulus, E=100×109Nm2 Length, L=6.336m Elongation, ∆L=1.21×10-3m Mass, m=29kg a.…
Q: The shaft shown in the figure is made of a material having 225 MPa. An axial load of 45 kN and…
A:
Q: A hollow bar with an outer diameter of 25 mm and an inside diameter of 18 mm carries a tensile load…
A: Tensile load = 100kN Outer diameter D1 = 25 mm inner diameter D2= 18 mm
Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…
A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…
Q: A wooden dowel is subjected to a shearing force of 715N on its top cylindrical face. If the dowel…
A: Shearing force F=715 N, diameter of dowel d=3cm (radius r=1.5cm), height of dowel h=11 cm and shear…
Q: A 16.7 cm long tendon is found to stretch 4.22 mm when a force of 15.8 N is applied to it. If the…
A:
Q: Two solid cylindrical rods support a load of P = 37 kN as shown in Figure below. R has a diameter of…
A: We know that we first draw a free body diagram of the system given as Now We calculate the angle…
Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…
A: Given that,Force : F = 557 (N)L = 66 (m)Area : A = 2.8 (mm2)Y = 1×1011 (N/m2)Here we need to find…
Q: A leg has 1.4 m shaft of bone with an average cross sectional area of 3x10-4 m². What is the amount…
A:
Q: The screwgate carabiner is left open as it is loaded by a rope as shown. Calculate the stress state…
A: Stress is defined as force per unit area. σ=FA Where F is a force and A is cross-section area.
Q: A solid copper cube has an edge length of 82.4 cm. How much stress must be applied to the cube to…
A: Write the given values with the suitable variables. L1=82.4 cm=0.824 mL2=82 cm=0.82 mK=1.4×1011 N/m2…
Q: A 47-kg woman stands on a vinyl floor wearing stiletto high-heel shoes. If the heel has a diameter…
A:
Q: 2B. A rigid bar ABC is pinned to the ground at B, with a cable support connecting to the wall. A…
A: This is a question regarding the stress created by a force acting on a body. The shear stress is the…
Q: a metal rod with length 2 m and cross sectional area of 0.002 m2 has a youngs modulus of 20x10^10Pa.…
A:
Q: A punch for making holes in steel plates is shown in Fig. below. Assume that a punch having diameter…
A: Hence the answer..
Q: A 90 kg construction worker stands 2.0 m from the right end of a 6.0 m long, 600 kg steel beam as…
A: First we find the tension in the cable . The forces acting are shown below: where m1 is the mass of…
Q: A force is applied to a circular surface with area 70 cm². The surface is parallel to the x-y plane.…
A:
Q: A cylinder has length L=40.5 cm and radius R=10.5 mm experiences a force F=67 kN as in Figure 6. It…
A: Given: The force experienced by the cylinder is F = 67 kN The length of the cylinder is L = 40.5 cm…
Q: 9.7)A bin weighing 8 tons is supported by three steel tension rods. Each rod is gin. in diameter.…
A: Given:- Bin weight = 8 tons- Each rod diameter = inchTo Find:Stress in the rods
Q: A wire has 20 x 10^10 N/msquared young modulus. Its diameter is 1mm that can handle a tension of 0.2…
A: Given data- young modulus= 20×1010 N/m2 1mm diameter can handle a tension of 0.2 kN.
Q: = Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the…
A: Determine the minimum diameter required for each of the three rods. Given, Loads:P=35 kipsQ=25…
Q: An Aluminum cable of length 3.5 m has 15,000 N tensile force acting on it, if the wire is only…
A: Given, The length of the alumunium cable, L=3.5 m The tensile force acting, F=15000 N Length by…
Q: To stretch a relaxed biceps muscle 2.5 cm requires a force of 25 N. Find the Young's modulus for the…
A: We must ascertain the muscular tissue's Young's modulus. We are aware that the biceps muscle can be…
Q: A 406-N object is hung from the end of a wire of cross-sectional area 0.05 cm². The wire stretches…
A: The longitudinal stress on a wire is given by σ = FA, where F = the force acting on the wire and A =…
Q: Please no hand writing solution
A: Given that diameter of a solid circular shaft,D=2'' Applied torque,T=9 kip.in Strain ,ε=305×10-6
Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Both rods AB and…
A: Given that: Diameter: D= 50 mm
Q: The stress experienced by a certain surface is 17612Pa when a 17-N force is applied to it. How much…
A:
Q: firefighter weighs 730 N. She wears shoes that each cover an area of 309 cm2. (a) What is the…
A:
Q: A hollow cortical bone has a maximum compressive stress of 185 MPa. This bone has an area of 6.4…
A: Write the given values with the suitable variables. σ=185 MPa=185×106 PaA=6.4 cm2=6.4×10-4 m2 Here,…
Q: the ankle joint therefore pushes upward on the bottom of the tibia with the force of 2800 N while…
A:
Q: The hollow steel cylinder DNGL, fixed on one end, is subjected to two torques and an axial load, as…
A: Area of the hollow cylinder is find by the A=πRO2-RI2
Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…
A: Given : Force, F = 557 N Original length of the cable, L = 66 m Cross-sectional area of the cable, A…
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images