helf Two shunt generators and a battery are working in parallel.The open-circuit voltage, armature and field resistancesare 240 V, 0.25 ohm, 100 ohms and 238 V, 0.20 ohm, 100ohms, respectively. If the generators supply the samecurrent when the load on the bus bars is 80 A. Calculatethe emf of the battery if its internal resistance is 0.172ohm.

Given Eg1=240 VRa1=0.25 ΩRsh1=100 ΩEg2=238 VRa2=0.20 ΩRsh2=100 ΩI=80 A

Two shunt generators and a battery are working in parallel. The open-circuit voltage, armature and field resistances are 240 V, 0.25 ohm, 100 ohms and 238 V, 0.20 ohm, 100 phms, respectively. If the generators supply the same current when the load on the bus bars is 80 A. Calculate the emf of the battery if its internal resistance is 0.172 nhm.

Two shunt generators and a battery are working in parallel. The open-circuit voltage, armature and field resistances are 240 V, 0.25 ohm, 100 ohms and 238 V, 0.20 ohm, 100 phms, respectively. If the generators supply the same current when the load on the bus bars is 80 A. Calculate the emf of the battery if its internal resistance is 0.172 nhm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

P2/ For the holowing circnit, find Vab using Syperposition. theorem. me 4A
Q1: Calculate the frequency of oscillation for each circuit in Figure below and identify the type of oscillator. Assume Q > 10 in each case. +10 V +9 V R₁ ww C₂ C₁ 470 pF 4 5 mH (a) 000 LUF 100 pF 1₁ Luf R₂ C₂ 1000 pF (b) C₁ LuF R₁ 4₁ mon 1.5 mH R₂ www R4 R3 1 μF L₂ mon 10 mH
R VO ac Sa ine Itage
DeVelo? the state eguatonnoutpt eguehom for the fdlocsiny cet F Volt
This is a second order LTI system subject review question, therefore it is not graded. 1.) Find the value of the R1 (Resistor) with the given values of R1= 80 ohms C=2uF and C1=2uF and cut off frequency of 1 kHz. 2.) Solve for the Final Output Voltage. Upon using multisim probe, the answer should be around 330mV.
What is the potential difference ( in volts) across C2 when C1 = 5.0 µF, C2 = 15 µF, C3 = 30 µF, and Vo = 59.8 V? %3D C, C, C3 Vo
R₂ Vin R₁ www RL Yout Calculate vout if R₁ = R₂ = 100 k, RL = 100 02, and Vin = 2 V. The value of the output voltage is XV.
Analogue 2
R2 ee Vin Vout Vout thi R2 Vin Vont
Various parameters of Schering bridge are given as follows. The voltage supply of 2 kHz is connected to terminals A and C and detector to points B and D. Arm AB comprises the unknown Resistor R1 and capacitor C1. Arm BC consists of resistor R2 of 18k 2. Arm DA consists of capacitor C2 of 0.06 µf. Arm CD has R3 of 1.5k2 and C3 of 2nf are in parallel. Calculate (i) the capacitance (C1) (ii) the equivalent series resistance (R1) and (iii) dissipation factor. Also draw the schematic diagram.
Consider the buck converter in Figure 5, with a DC voltage source, Vg = 100V and a load resistance, R equals to 2002. It is required that this converter delivers at least 100W to the load (output power). Assume the switching frequency is 100 kHz. Q₁ L 000 + i(t) D₁ C R>V iD(t) Figure 5 Determine the following: i. Critical value of the inductor, Lcrit ii. Converter voltage gain for inductor value, L = 0.1x Lcrit
Apply the junction rule to junction b in Figure. Is any new information gained by applying the junction rule at e? (In the figure, each emf is represented by script E.)