. Two shafts A and B whose axes are intersecting but inclined to each other at 20° are connected by means of a universal joint. A flywheel of weight 200 kN and radius of gyration 100 mm is fitted to shaft B. If the shaft A rotates at uniform speed of 2000 rpm, how can you calculate the maximum torque in shaft B?

. Two shafts A and B whose axes are intersecting but inclined to each other at 20° are connected by means of a universal joint. A flywheel of weight 200 kN and radius of gyration 100 mm is fitted to shaft B. If the shaft A rotates at uniform speed of 2000 rpm, how can you calculate the maximum torque in shaft B?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Suppose a 30 lb truck wheel 18 in. in diameter has a radius of gyration of 4 in. and the 6120 lb truck’s weight is distributed equally to each of the four wheels.a. If the truck can supply 150 lb x ft of torque to each wheel, how fast would the wheel want to accelerate if it didn’t slip? b. What would the coefficient of friction have to be in order to keep the wheel from slipping
Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axis are 30o. Produce a graph of velocity ratio against angle for f to proof the calculated results.
Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels connecting A and C having a module of 2 mm and those connecting C and B have a module of 3.5 mm. Speed of B is less than 1/10th that of A. If the two pinions have each 20 teeth, find suitable number of teeth for the wheels to improve the performance of the mechanism, the actual velocity ratio, and corresponding center distance of shafts C and A.
Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axes are at 60o to each other. Produce a graph of velocity ratio against angle for ? to proof the calculated results.
The crankshaft of a vertical sıngle-cylinder engine, stroke 250 mm, rotates at 300 r/min The reciprocating parts ( including part of the connecting rod) have a mass of 100kg The connecting rod has a mass of 120 kg, it is 450 mm long, the centre of mass is 300 mm from the gudgeon pin axıs and the radiųs of gyration about the same axıs is 363 mm When the crank is 30° from the t dc position and moving downwards, determine 31 the side thrust on the cylınder walls due to the inertia of the reciprocatıng parts, and 32 the crankshaft torque on the crankshaft due to inertia
A 1.5 in diameter 10-spline shaft and permanent fit has a compressive force of 2000 lbs. Find the torque applied if hub length 2 in.
(a) (b) 200 mm (c) A 600 mm B 200 mm с Fig. 3 Fig. 3 shows the layout of a shaft that rotates 500 rev/min and is supported by bearings at O and C. The shaft is carrying two gears at point A and B, in which the pitch diameter of Gears A and B are 500 mm and 250 mm, respectively. The force, PA applied at Gear A is 3.5 kN. The rotating shaft is made from AISI 1030 steel, and the factor of safety is 3. PB PA= 3.5 kN List down 2 assumptions needed in designing the shaft in Fig. 3. Design the minimum allowable diameter for the shaft at its critical location. The bearings at points O and C are required to have a desired life of 25kh at a speed of 500 rev/min. Based on these conditions, select the appropriate bearings for this
The equation of the turning moment diagram for the three crank engine is given by:where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
Flywheels are used to smooth out fluctuating torques such as produced on the crank of piston engines. The diagram shows a torque - angle diagram for a certain machine. The speed of the shaft must be maintained between 490 and 510 rev/min. Calculate the moment of inertia of a suitable flywheel. Calculate the mass required if the radius of gyration is to be 0.3 m.
2. A shaft is supported on bearings A and B, 800 mm between centres. A 20 degrees straight tooth spur gear having 600 mm pitch diameter, is located 200 mm to the right of the left hand bearing A, and a 700 mm diameter pulley is mounted 250 mm towards the left of bearing B. The gear is driven by a pinion with a downward tangential force while the pulley drives a horizontal belt having 180 degrees angle of wrap. The pulley also serves as a flywheel and weighs 2000 N. The maximum belt tension is 3000 N and the tension ratio is 3: 1. Determine the maximum bending moment and the necessary shaft diameter if the allowable shear stress of the material is 40 MPa.
The problem is stated below. However, change the position of torque to point C from point D. What is the effect of variation of torque placement in shaft CB?
Q. An engine flywheel has mass of 6.5 tonnes, and the radius of gyration is 2 m. If the maximum and minimum speeds are 120 r.p.m and 118 r.p.m respectively, find the maximum fluctuation of energy.