Two rigid tanks, each filled with 50 kg of air, have temperature of 900 K and 400 K. A heat engine placed between the two tanks extracts heat from the high temperature tank, produces work, and rejects heat to the low temperature tank. Maximum work obtained from the tank is kJ. A 4925 B 4775

Q: Pictured below is a multiplication problem worked out using the Egyptian method and Egyptian…

A: Consider the given diagram and see row 1 and row 2.

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: 1-) b. 1+j 1 Evaluate a. 1+j

A: Ans(a)  j2=-1 Divide by 1-j both sides 1-j1+j×1-j1-j (1-j)21-j2=1+j2-2j2=-2j2=-j

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: Evaluate the following statement and determine whether it is True or False: "The specific heats for…

A: Specific heat (often denoted as "c") is a thermodynamic property that describes the amount of heat…

Q: In the figure shown, gear A rotates at 300 rpm. Gear S is fixed and has 80 teeth. The three…

A: Write the given data. Speed of arm, Narm=180 rpmSpeed of anulus gear, NA=300 rpmSpeed of gear S,…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: Question Completion In the figure below, which of the following represents the dedendum? zeta gamma…

A: Circular pitch is the distance measured from a point on one tooth to the corresponding point on the…

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: a) What is the reading (degrees, minutes)? b) What is the reading (degree and fractions of a…

A: Reading on main scale = 90 degreeReading of vernier matching with main scale = 22Least count of…

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: What is the gear ratio supplied by the gear system shown to the right? (It is a single pitch…

A: Here number of teeth in gear ( Tg)=30 Here number of threads/teeth in worm (tw)=5 For single pitch…

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 3.17 g coins…

A:

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: True

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: SHAFT KEY

A:

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: There are several failure modes by which gears can fail. Select the true statement from among the…

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

A:

Q: a. Determine the magnitue of P and F (in N) if the resultant of the five force shown is 1000N…

A: The given system of force is as shown below, The given forces are as follows. F1=840…

Q: If gear 1 turns 620 degrees, how many degrees will gear 3 turn? N1 =20, N2

A:

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

A: Given Gear train arrangement To find Gear train which will be effective for bearing

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A: As per given question  The radial distance measured from the pitch circle of a gear to the bottom…