Two researchers are to produce non-ferrous alloys materials. Researcher A is producing cast alloys while researcher B is producing wrought alloys. Both researchers are to add Pb as alloying element. Which of the two researchers can have more Pb as an alloying element and why? What precautions should the researcher with low Pb take during heat treatment or hot working?

Two researchers are to produce non-ferrous alloys materials. Researcher A is producing cast alloys while researcher B is producing wrought alloys. Both researchers are to add Pb as alloying element. Which of the two researchers can have more Pb as an alloying element and why? What precautions should the researcher with low Pb take during heat treatment or hot working?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter26: Welding Metallurgy

Section: Chapter Questions

Problem 26R

See similar textbooks

Similar questions

In the present figure: compare between the alloy number 1 (0.4% C) and 2 (1.2% C) regarding: A. The expected mechanical properties of the two alloys (with explanation). B. The range of applications for these alloys. C. The stages of annealing treatments including: 1) Softening 2) Spheroidizing 3) Grain Size Reducing.. Subject: Metallurgy
Show full work from basic,Thanks
Briefly describe how precipitation hardening happens in Al alloys (how the microstructure evolves as annealing time increases). Why it first forms q” then q’ before q is finally formed? How does the alloy’s strength change during this process? What are the strengthening mechanisms?
According to Reference [1], alloys of nickel (Ni) and tungsten (W) are can form substitutional solid solutions up to approximately 11 at% W. Consider two different alloy compositions: Ni-5W (5 at% W) and Ni-10.5W (10.5 at% W). A. Which composition should be more ductile? B. Which composition should be stronger? C. Using the oy~ C¹/2 relationship from the lecture slides, how many times larger should the yield strength be for Ni-10.5W compared to Ni-5W? D. Where should the tungsten atoms sit relative to the dislocation on or opposite the side with the extra half-plane? You will need information from Appendixes of the textbook.
3 Materials Science. From picture below.Describe in detail the phase transformations (showing cooling curves, corresponding optical backgrounds, etc.) that takes place during solidification of the following alloys:(a) 99% Cu - 1% Al(b) 96% Cu - 4% Al(c) 80% Cu - 20% Al
1 Plastic Deformation Occurs Through Dislocation Motion... ...so in order to make a material stronger, we should prevent dislocations from moving. For each of the following alloys, identify the strengthening mechanism and explain how it impedes dislocation motion: A. An aluminum alloy "inoculated" with TiB2 during solidification, producing a large number of small grains. B. Monel, a corrosion-resistant solid solution of Ni and Cu. C. An aluminum-lithium aerospace alloy containing precipitates of Al3Li. D. Wrought iron, which is often worked into complex shapes such as railings or furniture.
Give complete solution, include diagram if need.
Q6/ A. Show how the precipitation heat treatment of precipitation hardenable alloys differs from dispersion hardening process of composite material. B. What are the main constitutes of composite materials and what are the roles of each constitute?
Of the following alloys, pick the one(s) thatmay be strengthened by heat treatment,cold work, or both: R50250 titanium, AZ31Bmagnesium, 6061 aluminum, C51000 phos-phor bronze, lead, 6150 steel, 304 stainlesssteel, and C17200 beryllium copper.
You have an Al 2024 alloy with predominantly (Al) and some CuAl2 (450ºC and 3 wt. % Cu). Most of the CuAl2 has gotten larger and diffused to the grain boundaries to give you the microstructure shown below on the right side. After testing the hardness of the sample is determined that it's too soft and not mechanically strong enough. Being specific regarding temperatures and times (or endpoint conditions), develop a method to make the Al 2024 alloy as hard as it can get. Show microstructural diagrams after each step.
Q1] Alloying elements have a major influence on steel. Explain their effect or corrosion resistance and hardness properties. Also classify steel according to alloying elements percentage? (5Marks)
Metal working Fe-C: What are possible sources of error in trying to obtain a specific hardness or strength? Not errors of hardness testing. Talking about working the metal (tempering, normalizing, quenching, etc.) to try to achieve specific hardness or strength.