6. A stationary tow-truck is using a winch to pull a car along the road toward the truck. The winch is pulling the line in at 10cm/s and the top of winch is 2.5m above the ground How fast is the car moving towards the truck when it is 20m away from the truck along the road? 2.5 m

Q: ④ Comparision between forced and Induced draught.

A: (1) Fan is installed near or at the base of the boiler(2) It handles low temperature and less volume…

Q: Explain following: a. SIM and TIM b. Constitutive relation of SMA

A: Given SIM TIM SMATo find Definition of SIM and TIM Constitutive relation of SMA

Q: Write short note on compression ratio

A: compression ratio

Q: Multiple Versions Question: A double acting cylinder has a bore of 107 mm. The rod diameter is 32…

A: Given: The bore of the double-acting cylinder is D=107 mm =0.107 m, The rod diameter is  d=32 mm…

Q: Describe how the system works

A: A hydraulic system is a drive technique in which energy is transferred from an electric motor to…

Q: Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20…

A:

Q: Unusual smell during machine operation is cause to problem. Select one: True False

A:

Q: Mercury will always have a hairline lift. Select one: O True O False

A: False: Grammatical mistake ('has' is place of 'have') Also, in mechanical engineering context ,…

Q: Q4: A/Compare between single package and split type

A: Comparision between single package and split type

Q: hat is formula for friction factor?

A: Friction factor: This is also called the Darcy friction factor. It is used in the Darcy-Weisbach…

Q: For forced draft counter flow cooling tower a. fan is kept at top of cooling tower and air and water…

A: Solution:

Q: Backgrour grid Exit jet

A:

Q: If a wrench is unable to loosen a wheel nut, what are two ways that you could increase the torque…

A: There are two ways to increase the Torque if a unable to loose the wheel nut

Q: for velocity one find the total gear ratio and not velocity

A: the output speed is:Here negative sign is just indicating the opposite direction of the rotations of…

Q: What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392…

A: Given Data: The speed of advance of the cylinder is, C=392 in/min. The diameter of the piston is,…

Q: Mercury will have always capillary raise. Select one: True False

A: In the event that we put capillary  mercury.   mercury have higher cohesive forces  contrasted with…

Q: Process control is generally referred as А. Process to enhance quality and quantity of final output…

A:

Q: A pipe has a Re of 1000, what is the friction factor?

A:

Q: Find a interpolation to viscosity of water at 26 degree

A: Here from the table of temperature and viscosity We have the Dynamic viscosity(η) of water at 26°C…

Q: Draw the block diagram of pressure measurement system with Analog Display.

A:

Q: Given two oil According to the standard by Society Automotive Engineers the oil , by comparing the…

A: Given: Given two oil According to the standard by Society Automotive Engineers the oil , by…

Q: why are you squaring the velocity in the eq

A:

Q: What is the mechanical advantage of an input piston with a diameter of 1.25" pushing fluid to move…

A: Diameter of input pushing piston, d1= 1.25" Diameter of output pushed piston, d2= 2"   To find:…

Q: Please draw/show a picture of atleast 15 PIPE FITTINGS that you know.

A: Here are the pictures of pipe fittings that we know. These pipe fittings are given as under,

Q: 2. Show the HGL and EGL for the conceptual system shown below for the following conditions: SHOW…

A: (a) Consider the diagram shown below for the EGL and HGL neglecting the minor losses.

Q: 100 KH 20 KN/m B 2m C am RI

A:

Q: The rest of the questions are thus: 4) Calculate the air temperature and pressure in the pump at…

A: Given R=287 J/kg.k= 0.287KJkg.k Cp=1.005KJkg.k y=1.4 P1= 1 bar= 100 kPa T1=298 K   Explanation:…

Q: how did you get the 3038Pa in static pressure?

A:

Q: a complete proc which is already

A: Butterfly valves with lugged, wafer, and double flanged seats, in all materials and seat types, are…

Q: Alm that He Cafle

A:

Q: Outline the difference between non associate and associated gas

A: Given Data- Question is given with topic related to gases we have to write difference between…

Q: What is the reason qhy HRSG HP, IP & LP drum separate from wet of ground using a wooden support…

A: 1. HRSG HP Drum (High-Pressure Drum) Separation from Wet Ground using Wooden Support :   To prevent…

Q: Reasons why coefficient of viscosity may be different in calculations from in graph

A: The proportion of the shearing stress to the velocity slope could be a degree of the viscosity…

Q: Write a brief procedure for measuring the vapor pressure of water

A:

Q: Why cascade system is the best choice for the above solution

A: A system or technique for connecting and running two induction motors so that the primary circuit…

Q: A reciprocating air compressor has cylinder with 30cm bore and 40cm stroke. Compressor admits air at…

A: Cylinder diameter of compressor or bore diameter (D) = 30 cm = 0.3 mStroke length of cylinder (L) =…

Q: 0/1 The weather has been hot. .many * weeks Since for to about

A: For is used in the sentence which talks about a period of time Example: for two hours for three…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.