Two pressurized prismatic tanks A and B are connected at their sides by an orifice 140 mm in diameter. Tank A contains water at a depth of 3 m above the orifice and a pressure of 50 kPa on the water surface. Tank B also contains water at a depth of 2 m above the orifice and a pressure of 15kPa on the water surface. The coefficient of discharge is 0.86 and the coefficient of velocity is 0.92. Detemine the: show complete solution, thumbs up guaranteed 1. What is the the head lost in the orifice? 2. What is the value of power lost?

Q: The nozzle which furnished the water to a certain hydraulicturbine 275 mm in diam. and has…

A: Flow rate: The amount of fluid flowing through a particular crosssection per unit of time is known…

Q: A pump can lift water at a dischargc of 0.2 m'/scc to a hcad of 30 m. The critical cavitation number…

A: Given   Critical cavitation factor = 0.144         Vapour pressure, Pv = 0.3 m…

Q: A pump is used to transfer crude oil from a non-pressurized oil tanker to a storage tank at a…

A: As all the units of the parameters in the given problem are irregular, convert all the units into SI…

Q: A pump is to be placed at the beginning of a 30 m long piping system consisting of 1-1/2 inch…

A: Release head differs with pull tank level. The response is yes. Assuming you bring down the pull…

Q: The diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: dl Calculate the volumetric flow rate of water through a pipe with an inside diameter of 0.18 m…

A: d1=0.18m , d2=0.11m x=0.3m , Cd=0.67

Q: The diameter of an open topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: is type of device based on its construction, used in applications where it's necessary with low…

A: All are the flow rate measuring device based on the pressure difference and the stagnation point…

Q: Liquid of sp.gr and u is in a closed tank with air at pressure measured by a manometer of R reading.…

A:

Q: Determine the head loss in a pipeline with friction factor of 0.01, length of 0.8 km, diameter of…

A: Given data: friction factor (f) = 0.01 Length (L) = 0.8 km Diameter (D) = 0.9 m Speed (V) = 8 m/s

Q: Liquid propane, at its bubble point, is to be pumped from a reflux drum to a depropanizer. The…

A:

Q: Two vertical circular cylindrical tanks are connected near the bottom by a short tube having a…

A:

Q: Water from a nearby lake is to be used for a fountain and a water tank. The figure below shows the…

A:

Q: Water is retained in a small mountain lake whose surface is 280 ft above the inlet to the turbines…

A: Bernoulli's theorem is used in fluid dynamics and gives the relationship between the pressure,…

Q: Water flows between two reservoirs A & B. The water level in A is 400 m AOD and in B is 385m AOD.…

A:

Q: Industrial pipes Do the guides allow movement of a pipe only in two directions (in a plane)?

A: The objective of the question is to understand the movement of a pipe in a guide in terms of…

Q: 5.9.5. Factory tests indicated that a cavitation parameter for a particular pump is o = 0.075. The…

A: Given: Cavitation parameter for the pump→σ=0.075  Pressure at the sea level→Patm=101.325 KPa…

Q: 8. Given the following venturi meter and the two pressures shown, calculate the mass flow rate of…

A: As per given question we have defind Mass of flow rate of in the circular pipe?

Q: A pitot-static tube with an instrument coefficient of 0.94 is used to  determine the air velocity in…

A: To find: The air velocity. Given: The instrument constant is Cd=0.94. The density of the air is…

Q: Determine the loss of head due to sudden enlargement when the velocity of water in the smaller pipe…

A:

Q: A rectangular duct whose cross-section has a w of 3 m and a h of 1.5m is used to transfer cooled…

A: Given:b=3 mh=1.5 m

Q: Water is pumped from the river through a 45-mm-diameter hose having a length of 2.5 m. The friction…

A:

Q: Water is pumped up through an inclined pipe to supply water on to a ridge. The diameter of the pipe…

A: This steps contain all the given data.

Q: Comment on the velocity in the pipe. Is it laminar, is it turbulent?

A: The comment on the velocity. Is the flow is Laminar or Turbulent?

Q: The volume flow rate of water that recirculates from the blade outlet to the impeller is estimated…

A:

Q: 12. A mixture of oil and gas flows through a horizontal pipe with an inside diameter of 150 mm. The…

A: We have mixture of oil and gas.Let assume that we have gas in x fraction of area.then (1-x) fraction…

Q: How does the manometer reading of the Orifice Meter apparatus affect its discharge? If the flowrate…

A:

Q: What is the hydraulic diameter of a pipe with a rectangular cross section of width w and length…

A:

Q: What power must be supplied by the pump to the fl ow if water (T = 20°C) is pumped through the…

A: Power of pump is 633.56 kW.

Q: Design the duct system shown below using Equal friction method, and determine the fan power when the…

A:

Q: Determine the size of the cylinder for a double acting al ressor of 50 kW indicated power in which…

A: Givendouble acting air compressor indicated power IP=50kWP1=110kPaT1=25oC=298KPV1.2= constant…

Q: The volume flow rate of water that recirculates from the blade outlet to the impeller is estimated…

A:

Q: Liquid of sp.gr and u is in a closed tank with air at pressure measured by a manometer of R eading.…

A:

Q: As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the…

A: Given data Point A is on the surface of the oilPoint B is 6.71 m below the surface of the…

Q: review the example. Thank you very much  Question :  Determine the power required (Watts) to drive…

A: Given:Speed of the pump, N=1 rpsDischarge of oil, ρ=850 kg/m3Flow rate, Q=375.3 gpmbore, d=250…

Q: The diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: Water flows through the piping junction, entering section 1 at 20 US gallons/min (1 US gal = 3.78…

A: Given data: Q1=20 US gallons/min=12.62×10-4 m3/sv2=2.5 m/sdh=1 mm Need to determine the exit…

Q: Water is supplied in a 2-in. dia. pipe at the rate of 2 cfs to a 10-hp, SO-percent efficient pump.…

A: The Answer is below

Q: Identify the device that is used to determine the discharge of a fluid flowing through a pipe.

A: The energy meter measures the units of electrical energy consumed by the given load. Pitot tube…

Q: I have a question from my fluid power enginneering class. The question was, standard hydraulic oil…

A: Given: Pressure at the pump outlet is 10 psi. Height of uphill is 100 ft. Flow rate is 10 gpm.

Q: Consider water flowing through a water hose of length of 100 ft, diameter of 3/8 inch, and average…

A: Length of the hose (L) = 100 ft =30.38 mDiameter of the hose (D) = 3/8 inch = 3/8 * 1/12 ft =…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.