Two pots are identical except that the flat bottom of one is aluminum, whereas that of the other is copper. Water in these pots is boiling away at 100.0 'C at the same rate. The temperature of the heating element on which the aluminum bottom is sitting is 156 °C. Assume that heat enters the water only through the bottoms of the pots and find the temperature of the heating element on which the copper bottom rests. Tcu= i

Two pots are identical except that the flat bottom of one is aluminum, whereas that of the other is copper. Water in these pots is boiling away at 100.0 'C at the same rate. The temperature of the heating element on which the aluminum bottom is sitting is 156 °C. Assume that heat enters the water only through the bottoms of the pots and find the temperature of the heating element on which the copper bottom rests. Tcu= i

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.50P: 2.50 Compare the rate of heat flow from the bottom to the top of the aluminum structure shown in the...

See similar textbooks

Similar questions

Two containers are alike except that the flat base of one is brass, and the other is silver. Water in these containers is boiling away at 100.0 degrees Celcius at the same rate. The temperature of the heating component on which the brass base is sitting is 175.0 degrees Celcius. Assume that heat enters the water only through the bases of the containers and find the temperature of the heating component on which the silver bottom rests.
A 15 lb. block of brass with a specific heat of 0.089 is heated to 189°C and the immersed in 5 gal. of water at 66°C. What is the final temperature of the brass and water? Assume there is no heat loss.
To determine the specific heat of an object, a student heats itto 100 °C in boiling water. She then places the 34.5-g object in a151-g aluminum calorimeter containing 114 g of water. The aluminum and water are initially at a temperature of 20.0 °C, and arethermally insulated from their surroundings. If the final temperature is 23.6 °C, what is the specific heat of the object? Referring toTable 16-2, identify the material in the object.
how many hyl of steam at 1600k and 0.20mpa can be safely placed in a tetrahedron conrainter with edge of 3.373m?
What is the answer? AQuestion A or B?
A 10 gallons of water has an inital temperature of 25 degrees Celsius. What is the input power needed to raise the temperature up to the boiling point after 25 minutes Assume heat loss 12%
Find MLT form for the (P/ρV2)
Describe what a "heated zone" is, how it works, and any constraints that may apply to it.
Refer to Table 3.3 in the lecture and take the data for water and the five other liquids listed in the table. Plot the data in a graph with the thermal conductivity on the vertical axis and the temperature range from 0°C to 100°C on the horizontal axis. Use colors or different dashed lines to make the graph presentable and understandable. The graph should look like the graph in Figure 3.1 in the lecture. Provide a short explanation of the graph in three to five sentences.
again i am uploading this question please explain The amount of heat extracted in the evaporator of the refrigerator is small as compared to the heat rejected in the condenser. Therefore when the door of refrigerator is kept open it does not cool the room but instead it heats up the room because less heat extracted from the room is less as compared to the heat rejected to the room. Therefore a person will feel warm while sitting in front of the open refrigerator inside the room. However if the refrigerator is lying in the open, then it will no way effect the feel of warmth or coldness to the person.
Discuss the concept of real-time thermal monityoring system.
no previous attempt please