Two parallel shafts A and B, 36 in. apart, are connected by a belt drive. The driving pulley rotates at 250 RPM and the driven pulley at 600 RPM. The smaller pulley diameter is 10 in. Draw the figures or diagrams, and for both open belt and cross belt, determine the following; 1) the diameter of the larger pulley 2) the linear velocity of the belt (ft. / min.), and 3) the length of the belt.

Two parallel shafts A and B, 36 in. apart, are connected by a belt drive. The driving pulley rotates at 250 RPM and the driven pulley at 600 RPM. The smaller pulley diameter is 10 in. Draw the figures or diagrams, and for both open belt and cross belt, determine the following; 1) the diameter of the larger pulley 2) the linear velocity of the belt (ft. / min.), and 3) the length of the belt.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A and C). All dimensions are in millimeters and all shoulder fillets (at points where diameter changes) have a radius of . The pressure angle for the spur gear at B is . The pressure angle for the bevel gear at D is and the bevel angle is . Note that the shaft is designed so that only bearing A takes thrust. The shaft is made of steel with . All the critical surfaces are ground. The shaft rotates at . A motor with a power of is connected at the bevel gear through another bevel gear. This drives the shaft. A load is connected through another spur gear at the output spur gear at B. The standard deviation on the power is . (a) Determine the forces acting on the gears. Recall that for a spur gear, the relation between the tangential component of the force and the radial component of the force and the pressure angle is given by . For this bevel gear, the axial (thrust) component of the force on…
2. PLease help
Please draw the figure. Thank you so much.An engine flywheel and a clutch plate are both connected to a transmission shaft. Let the moment of inertia of the flywheel be I1 and its angular velocity ω1, and let the moment of inertia of the clutch plate be I2 and its angular velocity is ω2. The two discs have then been combined by forces which are applied at their axes of rotation so as not to cause any torque. The discs then reached a common final angular velocity after rotational collision. Find the expression for the final angular velocity.
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC = 70 Teeth and ND = 120 Teeth Calculate the output angular velocity at Gear D (ωD). Give your answer in rads-1to the nearest radian.
Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axes are at 60o to each other. Produce a graph of velocity ratio against angle for f to proof the calculated results.
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
A flywheel drives a collar via link. The flywheel rotates at an angular velocity of 18 rad/sec clockwise. For 25° 2 Using ICR, determine: (a) the angular velocity of the link, (b) the velocity of the collar. d₁ = 75 mm d₂ = 260 mm NOTE: this is the same problem from this homework. but you must solve using ICR for B
Shaft A with 9 inches diameter cylinder running at 190 rpm is connected to shaft B by means of 24 inches diameter cylinder. Another cylinder on shaft B, 14 inches in diameter, is connected to 10 inches diameter cylinder on shaft C. Find the speed of shaft C. SPEED OF SHAFT C:
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
I need the answer quickly
The maximum sliding velocity of the teeth of two gear wheels in mesh is 0.32 m/s. The wheels are of module 5 mm and have 32 and 44 teeth respectively. The addendum for each wheel is 1.2 times the module and the pressure angle is 20°. Calculate: 2.1. The number of teeth in contact. 2.2. The angular speed of each wheel.
d. The mechanism shown in Figure 7.13 is a common punch press designed to perform successive stamping operations. The machine has just been powered and at the instant shown is coming up to full speed. The driveshaft rotates clockwise with an angular velocity of 72 rad/s and accelerates at a rate of 250 rad/s2. At the instant shown, determine: a. Draw the Kinematic Diagram b. Draw The velocity polygon and find the Velocity of Points A and B c. Draw the acceleration polygon and find acceleration D. a = 250 radis O- 72 rad/s 1.0" 60 4.0