Two meshing helical gears are mounted on parallel shafts that have rotational speeds of 1000 and 400 rev/min. The helix angle 30 degrees and the center distance is 252 mm. The gears have a module of 6 mm. Determine the normal circular pitch and the transverse circular pitch. Also, determine the number of teeth on each gear. A P^n=17.32 mm, p=20 mm,N1=24, N2= 50 B P^n=16.32 mm, p=18.85 mm,N_1=24, N_2= 60 p^n=16 mm, p=20 mm,N1=20, N2= 60 (D none of them

Two meshing helical gears are mounted on parallel shafts that have rotational speeds of 1000 and 400 rev/min. The helix angle 30 degrees and the center distance is 252 mm. The gears have a module of 6 mm. Determine the normal circular pitch and the transverse circular pitch. Also, determine the number of teeth on each gear. A P^n=17.32 mm, p=20 mm,N1=24, N2= 50 B P^n=16.32 mm, p=18.85 mm,N_1=24, N_2= 60 p^n=16 mm, p=20 mm,N1=20, N2= 60 (D none of them

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP, if you cannot answer it please reject it.
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
please solve it using FORCE METHOD. Thank you. only HANDWRITTEN answer needed ( NOT TYPED)
The change in diameter of the large steel bolt is carefully measured as the nut is tightened. Knowing that the initial diameter d = 50 mm, E = 190 GPa, and ? = 0.27, determine the internal force in the bolt if the diameter is observed to decrease by 0.009 mm after the nut has been tightened. Assume that the supports shown are fixed and rigid. d
asap
The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force (P) acting on the member is 25 KN, determine the maximum shearing stress developed within among the bolts. Strap Plate Member Plate P← P (9
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
The indicated bridge girder is subject to a differential temperature increase equal to 20°C (T1 = 40°C, T2 = 20°C). Using Cross's method, draw your DMF. Suppose: Beams and Columns of 0.5 x 0.5 m. α = 10^-5/°C Average ambient temperature= A =30°C 4.0 m 4.0 m 4.0 m T1 T2 3.0 m
Que. 2 A steel plate is 30 cm wide and 10 mm thick. A rivet of nominal diameter 18 mm is driven. The net sectional area of the plate is L 1.95 10mm
Answer 15&16
Within few minutes