Two members AB and AC are made of material with E- 77 Gpa and each member has cross sectional area of A= 425 mm2. The members are used to support bar BC. If P=2314 N, L1= 220 mm, L2= 340 mm and L3= 674 mm. Answer the following questions. L3 E L1 12 The tension in member AB=

Q: force members in the bars and state the

A: Given: A struss To determine forces in all members

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: To find: The tension in each cable and the reaction at A. Given: The height of the pole is 6 m. The…

Q: If the roller A is replaced by a pin, determine the corresponding reactions at A and then Identify…

A:

Q: 2.) The plate is supported by a pin in a smooth slot at B. What are the reactions at the supports?…

A: Given:The diagram of the problem is given below;

Q: AF, = 153 N load and a F2 = 99 N are applied to the frame which is supported by pins at A and B.…

A:

Q: A solid stepped bar is made of steel (E = 29 x 10³ ksi, v=0.25) and is fixed on both ends by rigid…

A: Given data  L= 3 in D = 1.4 in d = 0.5 in E = 29 × 10^3 ksi.   V= 0.25 Find the reaction RA

Q: the force in member (DF) is equal to.

A:

Q: 6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire…

A: Tension occurred in a cable due to stretch or pulled It is an internal force that acts all along the…

Q: The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of…

A: Given data: The modulus of elasticity in aluminum bar is E1=70 GPa=70×103 MPa The modulus of…

Q: Ql: The rigid bar ABC, attached to two vertical rods as shown in Fig. below, is horizontal before…

A:

Q: A compound bar has a given assembly with P1 on point B and P2 on point D. Modulus of Elasticity for…

A:

Q: 600 N 0.4 m 04 m 03 m- -0.3 m03 m03 m- The frame shown is supported by fixed support at E and smooth…

A:

Q: As shown in the figure, the member is anchored at A and section AB lies in the x–y plane. The…

A: Part 1 To calculate moment about AB we have MAB=μAB.γAC×FUnit vector is given…

Q: The cylindrical bar composed of two parts (AB and BC) is fixed at ends A and C. The two parts are…

A:

Q: The frame shown is fitted with three 36 cm diameter frictionless pulleys. A force of F = 920 N is…

A:

Q: Two members AB and AC are made of material with E= 138 Gpa and each member has cross sectional area…

A:

Q: Show a free body diagram of the left section. Find the forces in the members listed by the Method of…

A: Consider a section which cuts the members BD, BE, and CE. The free-body diagram of the right portion…

Q: The assembly is subjected to a tension force P = 2500 N. If these cables are arranged in a parallel…

A:

Q: The bar ABCD has rigid supports and consists of three prismatic solid segments, as shown. The end…

A:

Q: Figure 5m 2m 1m 1.5m. B D y 2 m 1 of 1 > E Submit Part B Determine the force in the member BD of the…

A: F=(-220 i + 380 j) N   To find out :- The force in the member AD and BD of the truss and state if…

Q: The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional…

A: GivenW=44kNA=178.5mm2E=71GPa

Q: 2-12. For the truss shown in the figure, deter- mine the total elongation of the member BC due to…

A:

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Data given-  F = 600 N  Force in member CE ?

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 33…

A:

Q: The truss shown in the figure is applied with force P = 5 KN. Which of following nearly gives the…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 30…

A: Solution:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 30…

A:

Q: The cantilever truss in the figure is hinged at D and E. Find the force in member CE.

A:

Q: 1,200 N-m 4,500 N-m 2,800 N-m 500 N-m (3) B 0.70 m 1.80 m 0.70 m Complete the torsion diagram of rod…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31…

A: According to this principle, if member is subjected to various loading then the resultant load will…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 30…

A:

Q: Q2 Two members AB and AC are made of material with E= 102 Gpa and each member has cross sectional…

A: GivenE=102GPa=102×103 N/mm2A=489mm2P=811NL1=202mmL2=313mmL3=443mm

Q: The structure above is subjected to a load at point C. Using the table below, determine the forces…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 31…

A: F1=31 kipsF2=13 kipsF3=24 kipsF4=37 kips

Q: Given: Truss ABCDE below. P1 = 6 kN P2 = 8.6 kN Find: The magnitude of the force in each member and…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.