Two long, parallel wires are 6 m apart. They carry steadycurrents of 10 A each, in opposite directions.Place a third long wire in parallel with the two wires, at a distance of 5 mfrom each of the two wires. If we run a steady current of 10 A through thethird wire, determine the force per unit length acting on the third wire bythe other two wires. Use drawing to present your analysis. Make clear thedirections of the currents and the force with these three long and parallelwires.

The magnetic field created at a point due to a current carrying conductor is given as: B=μ0I2πR…

Two long, parallel wires are 6 m apart. T nts of 10 A each, in opposite directions. a third long wire in parallel with the two wires, at each of the two wires. If we run a steady current of wire, determine the force per unit length acting on her two wires. Use drawing to present your analysi ions of the currents and the force with these three

Two long, parallel wires are 6 m apart. T nts of 10 A each, in opposite directions. a third long wire in parallel with the two wires, at each of the two wires. If we run a steady current of wire, determine the force per unit length acting on her two wires. Use drawing to present your analysi ions of the currents and the force with these three

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A solenoid similar to the figure below, has a core made of cast steel (refer to the figure on the next slide). It has a cross-sectional area of 4cm2 and a mean length of 20cm. The coil has 100turns, and the coil current is 3.2A. Find the following: d)Permeability, μ e) the relative permeability, μr f) the core reluctance, R and g) the flux, Ø
An iron core 0.4 m long and 5 cm2is wound with 300 turns. When a current of 0.5A flows in the coil, how much is the inductance of the coil. Assume the core has a permeability of 2500.
Consider two infinitely long parallel wires. The wires are separated by a distance of 10 cm. Both wires carry a current of 5 A but in opposite directions. Compute the force per unit length on wire 2 due to the current in wire 1.
Q2. Determine the current Ii required to establish a flux of o -4 x 10 Wb in the magnetic circuit of figure below, draw the equivalent circuit and find the circuit inductance given (4. - 2800 H/m). Lg - 0.2 cm Sheet Steel I I-0.28 A N2 - 200 turns A- 1.6 x 10+ m' N - 40 turns Labed - 20 cm
Two thin parallel wires carry current in the same direction. The force exerted by one wire on another, Please choose one: a.It is perpendicular to the wires and attractive. b.It is perpendicular to the wires and repulsive. C.It is parallel to the wires. D.It is zero.
2. A C-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm². Next find the flux flowing thru the C-core.
1. A magnetic circuit constructed of sheet steel has an average length of 1.5 m and cross sectional area of 0.025 m². A 50 turns coil wound on the ring has a resistance of 0.8 Q and draws 4 A from A DC supply. The relative permeability is 5000. Determine a) The flux density. b) Voltage applied. c) If the material is replaced with another material with a relative permeability of 3000 and keeping the other parameters as it is then calculate the new flux and explain what happened.
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
The length of a magnetic circuit in a moving iron instrument is 300mm. The coil around the soft-iron core has 360 turns and takes a current of 1.75 A. The core is square in section with sides of 20 mm. Takethe relative permeability of soft iron as 1100. Determine the flux density
A P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN B Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. d₂ 1.2 m What is the normal stress in rod BC in MPa? Round to the nearest integer and enter the magnitude only. C
5. An iron core 0.4m long and 5 cm?. In cross section, is wound with 300 turns. When a current of 0.5 A flows in the coil, how much is the inductance of the coil. Assume the core has a pemeability of 2500.