Two loads are connected in parallel as shown to an AC voltage source of 60 Hz frequency. The total power consumed by the loads 1& 2 is P = 152 kW at PF = 0.9 lagging. The Load-1 power factor PF1 = 0.5 leading and Load-2 power factor PF2 = 0.7 lagging Find the power P2 (in kW) consumed by Load-2. (Hint: use the power triangle concept) PLEASE INPUT YOUR ANSWER IN KW I M Load-1 Load-2

Two loads are connected in parallel as shown to an AC voltage source of 60 Hz frequency. The total power consumed by the loads 1& 2 is P = 152 kW at PF = 0.9 lagging. The Load-1 power factor PF1 = 0.5 leading and Load-2 power factor PF2 = 0.7 lagging Find the power P2 (in kW) consumed by Load-2. (Hint: use the power triangle concept) PLEASE INPUT YOUR ANSWER IN KW I M Load-1 Load-2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
Question-2 Can you throw the emergency solution? I would appreciate it if you write legibly.
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
Question - 5 a. If i = Im sin wt is flowing through a series R-L branch, then derive the expression for voltage, impedance and instantaneous power. Also from the expression of power, explain reactive and real power with graphical presentation.
14- A load 100+j0 ohms is connected across a 200V and 50 Hz supply. Find the Power factor. a. Unity b. 0.4 c. 0.8 d. 0.6
Problem 3-An AC circuit is shown. The frequency is 1000 Hz. The source voltage is v(t) = 10 cos(2x1000) of clouent a) Find the impedance seen by the voltage souree b) Find the phasoj current delivered by the source. c) Find the phasor voltage across the resistor, Vr. d) Find the sor voltage across the capacitor, Ve e) Find the voltage across the capacitor, v.(1). 4 kQ 10/ 0 sine 1 kHz C C1 53 nF
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).
The load in a factory is 300 kW at 0.8 lagging power factor. It is required to improve the overall power factor to unity by using the synchronous motor taking 80 kW. Calculate (1) Power factor of the synchronous motor (2) Reactive kVA of the synchronous motor.
Please answer completely with accurate diagrams.
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…