Two links, made up of aluminum and steel, are connected by a hinge joint and an axial load P = 1000N is applied at node 3 as shown in Fig. 1.34. Determine the stresses developed in the two links using the finite element method. Link 1, Steel Link 2, Aluminum E=207 GPa; A=4cm2 E=71 GPa; A=2 cm? 3 40 cm 60 cm FIGURE 1.34 Two links subjected to an axial load.

Two links, made up of aluminum and steel, are connected by a hinge joint and an axial load P = 1000N is applied at node 3 as shown in Fig. 1.34. Determine the stresses developed in the two links using the finite element method. Link 1, Steel Link 2, Aluminum E=207 GPa; A=4cm2 E=71 GPa; A=2 cm? 3 40 cm 60 cm FIGURE 1.34 Two links subjected to an axial load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
if u don't know the answer skip it but try to take another expert please don't take it complexity please answer to another expert
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads are applied at the positions indicated. Find the maximum value of P in Newton that will not exceed a stress in steel of 150 MPa, in aluminum of 87 MPa, or in bronze of 97 MPa.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10 -3 mm while those at CD decrease 80 x 10 -3 mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 50 mm, b = 140 mm, and c = 80 mm.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 103 mm while those at CD decrease 60 x 103 mm in the 230- mm-gage length. Using E = 180 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c= 70 mm. gage length a mm A B. b mm c mm
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D