Two identical generators 5MVA, 6.6KV equally sharing a load of 8 MW at 6.6kV, 0.8 lagging p.f. The ractanctance between the internal voltage of each machine and the load bus is 2 pu. Both machines are equally excited. (a) Find the excitation emf for both machines. (b) If the excitation emf for machine-1 is increasesd by 20%, find the percentage change in Ea2 to keep the terminal voltage unchanged. Assume that the governor setting for both machine to remain unchanged.

Two identical generators 5MVA, 6.6KV equally sharing a load of 8 MW at 6.6kV, 0.8 lagging p.f. The ractanctance between the internal voltage of each machine and the load bus is 2 pu. Both machines are equally excited. (a) Find the excitation emf for both machines. (b) If the excitation emf for machine-1 is increasesd by 20%, find the percentage change in Ea2 to keep the terminal voltage unchanged. Assume that the governor setting for both machine to remain unchanged.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Quiq plz
A shunt generator delivers 195 A at a terminal p.d. of 250 V. The armature resistance and shunt field resistance are 0.02 2 and 50 2 respectively. What is the value of generated e.m.f. ?
4) A 40-kW induction motor, with a lagging power factor of 0.76 is supplied by a 120-Vrms, 60-Hz sinusoidal voltage source. Find the capacitance needed in parallel with the motor to raise the power factor to 0.9 lagging
• A generator driven by a wind turbine is required to deliver 1.5MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis. The rotor is designed to operate at a rotational speed of 22 rpm. • If the turbine delivers its rated power at a wind average speed of 22 mph, Calculate the corresponding diameter of the propeller and its TSR, assuming a typical value of 0.35 for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³.
A DC chopper controls the speed of PMDC motor. The motor has 0.52 armature resistance and 0.05H armature inductance. DC bus voltage is 300V. In a specific load condition, when the duty cycle is 0.5, the back EMF of the motor is 140V. The chopping frequency is 1kHz. a. Sketch the circuit b. Find the maximum and minimum values of the motor current. c. Calculate the power to the motor. d. Find the Fourier series expansion of the load (motor) voltage. e. Explain the motor behavior when duty cycle is decreased gradually. f. If a low-pass filter (LC filter) connected to the motor terminals, explain the operation of the circuit.
32. An alternator requires an alternating current of 2.1 A to produce on short circuit its full-load current of 50 A. The same on open-circuit an emf of 320 V. The armature resistance is 1Ohms . Find the full-load percentage regulation with a lagging p.f. of 0.6 when terminal p.d. on load is 2000 V. A. 7.2% B. 28.8% C. 3.6% D. 14.4%
What is reactive power compensation, explain why it is done by showing it on the power triangle and write its advantages in articles.
A 50 kW induction motor is operated at a lagging power factor of 0.8, the source voltage being 230 V rms. a) Find the complex power Sm that this motor is using. b) In order to get lower electricity bill it is desired to connect a parallel compensator to the motor so as to get pf%3D0.95 lagging and still provide the 50kW real power for the motor. Determine the total complex power ST= Sm+ Sc that will achieve the desired pf, where Sc is the power of the compensator c) Determine the complex power S. of the compensator and the . value of the parallel compensator impedance. What type of circuit element should be the compensator?
DC generators
How many different load groups are there in power plants? Explain by drawing on a power-time curve.
A 8 pole, series connected DC machine is being used as a window winder in an automobile application. An open circuit voltage of 28.20 V when running separately excited at 1160 rpm with a field current of 3.10 A. An armature resistance of 1.85 M and an armature inductance of 20 mH. A field resistance of 3.75 2 and a field inductance of 150 mH. If the window is jammed, calculate the current and torque when the motor is driven from a 30 V DC battery
If the average pole flux of a dc machine with 24 coils, each of which contains 16 windings, 4 poles, double layered parallel winding (duplex lap winding), with a speed of 1000 rpm, is 15mWb, what is the idle winding voltage and (Note: In your operations, two digits after the comma) take it)