Two identical bars A with the given length mm long support the rigid weightless beam shown. Another bar is placed exactly in between them, that is 0.14mm shorter. Determine the change in temperature in C for the middle bar to just touch the weightless beam. Bar A Bar B Lin mm 800 Ain mm 1100 950 E in Gpa 70 200 a in /C 0.000023 0.0000117 GAP BAR A BAR A BAR B

Two identical bars A with the given length mm long support the rigid weightless beam shown. Another bar is placed exactly in between them, that is 0.14mm shorter. Determine the change in temperature in C for the middle bar to just touch the weightless beam. Bar A Bar B Lin mm 800 Ain mm 1100 950 E in Gpa 70 200 a in /C 0.000023 0.0000117 GAP BAR A BAR A BAR B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hello tutor, in this question the answer is already given. From the picture attached, just please help me identify what is the value for Vmax = ? Mmax = ? You can choose for the answer in Vmax in the table Shear (kN) You can choose for the answer in Mmax in the table Moment (kN m)
A HA He 1 m L 1 m
statics rigid of bodies
(b) A solid circular rod as in Figure Q1(a) is 600 mm long and 20 mm diameter. The rod is subjected to an axial force of P = 50KN. Upon loading, the elongation of the rod is 8 = 1.40 mm, and its diameter reduce to d' = 19.9837 mm. Determine the modulus of elasticity of the material. Assume that the material does not yield.
Som.
AREA MOMENT METHOD Find the value of EIð at the point of application of the 200 N-m couple in the figure. 500 N 200 N-m 1 m 2 m 1 m R1 R2
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
MKOPO The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the corners B and D are subjected to the displacements that cause the rubber to distort as shown by the dashed lines. 3 mm- D 400 mm A 300 mm- B 2 mm X
A uniform bar AB weighing 424 kN, is fastened by a frictionless pin to a block weighing 200 kN as shown in figure below. At the vertical wall, f = 0.268 while under the block f = 0.20. Determine the force P needed to start the motion to the right.
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
statics of rigid bodies
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN