Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load P1 acting at the top is equal to 16 kN. The load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the rods are daB = 30 mm, taB = 12 mm, dec = 60 mm, and tec = 9 mm, respectively. Given %3D that the lower part of the rod has the same compressive stress as the upper rod. Examine the required magnitude for load P2.

Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load P1 acting at the top is equal to 16 kN. The load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the rods are daB = 30 mm, taB = 12 mm, dec = 60 mm, and tec = 9 mm, respectively. Given %3D that the lower part of the rod has the same compressive stress as the upper rod. Examine the required magnitude for load P2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

why is the external load not shown in the free body diagram of limk 2 and 4?
A triangular block shown in figure 4 is subjected to the loads S = 1,000-lbs and T = 2,000-lbs. If AB = 8” and BC = 6”, resolve each load into components normal (n) and parallel (p) to the side ‘AC’.
2. 1.5 m 3 m 400N 200 N 1 m Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member as shown. Which of the following is closest to the force in cable BC?
In Figure 1.2, the horizontal rigid beam ABCD is supported by vertical bars (1) and (2) and is loaded at points A and D by vertical forces P = 30 kN and Q = 40 kN, respectively. Assume that the dimensions a = 2.5 m, b = 2 m and c = 1.5 m. Determine the internal force of each bar. Answer: A a f₁ = 37.5 kN, f₂ = 32.5 KN L₁ B (1) b L₂ C (2) -X,U D
The cantilever truss in the figure is hinged at D and E. Find the force in member CE. 1000 Ib 60 60 30 lo lo00 16 |000 (b. O 3475 lb O 3375 lb O 3275 Ib O 3175 Ib
(a.)The figure below shows a steel rod of 25mm² cross-sectional area. It is loaded at four points K, L M, and N. Assume Esteel = 200GPA. Find the total change in length of the rod due to the four loadings. M 100N 250N 200N 50N 500mm 400mm 1700mm Figure Q.la: Steel rod
3. A structure frame is shown in Figure 3 experienced multiple applied forces at joints D and B. The frame is simply supported at A and C. Determine the force in each member of the truss and state if the members are in tension or compression. 300 N 400 N D 2m 250 N 2m B 200 N
The frame shown in Figure 3.1 has internal pins at points B, C and D and is supported by a pin at point A and a roller at point E. The loading consists of two concentrated loads and a point moment, as shown in the figure. a) Calculate the support reactions at points A and E. A 6 in. B -9 -9 in. →✦9 in. →✦9 in. →| 500 lb 700 lb ←9 in. D E Figure 3.1 - Compound Frame 2 kip-in 12 in. 12 in.
A 100N load is supported by a strong bar as shown in the figure. The tension in the cable is 200N. Compute the value of angle "A" in degrees. 10 m 200N 100N ZA ZB 10 m
I need to solve this question as soon as possible
please solve step by step and correctly
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPa. Aluminum A = 400 mm2 Bronze A = 200 mm2 Steel A = 500 mm² P 2P 4P 2.5 m 2.0 m 1.5 m