Two forces 1 and F, act along the two sides of an equilateral triangle as shown in the figure below. Point O is the intersection of the altitudes of the triangle. F F2 (a) Find a third force F3 to be applied at B and along BC that will make the total torque zero about the point O. (Use the following as necessary:F, for the magnitude of 1, and F2 for the magnitude ofF 2-) | 31 = (b) Will the total torque change if F3 is applied not at B, but rather at any other point along BC? Yes No

Two forces 1 and F, act along the two sides of an equilateral triangle as shown in the figure below. Point O is the intersection of the altitudes of the triangle. F F2 (a) Find a third force F3 to be applied at B and along BC that will make the total torque zero about the point O. (Use the following as necessary:F, for the magnitude of 1, and F2 for the magnitude ofF 2-) | 31 = (b) Will the total torque change if F3 is applied not at B, but rather at any other point along BC? Yes No

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

O F You push on a door 18 cm from the hinge with a force F that has components Fx=7 Newtons and Fy=17 Newtons (see figure). What is the magnitude of the torque about the hinge? Answer in Nm.
At the presentation ceremony, a championship bowler is presented a 1.58-kg trophy which he holds at arm's length, a distance of 0.655 m from his shoulder joint. (a) Determine the torque (in N · m) the trophy exerts about the shoulder joint when his arm is horizontal. (Enter the magnitude only.) Carefully draw a diagram which shows the force F which produces the torque for this situation, the vector i which locates the point of application of the force relative to the shoulder joint and the angle 0 between the direction of these two vectors. See if you can write a relationship that will allow you to determine the magnitude of the torque i if you know the magnitude of the vectors i and F, and also the angle 0 between their direction. N · m (b) Determine the torque (in N · m) the trophy exerts about the shoulder joint when his arm is at an angle of 35.0° below the horizontal. (Enter the magnitude only.) Carefully draw a diagram which shows the force F which produces the torque for this…
PROBLEM SET B 1. How much torque is produced by opening a jar of pickles if the lid on the jar has a radius of 3.5 centimeters and the force exerted tangentially to the lid is 150 newtons? itudo of gravitational
Suppose you exert a force of 195 N tangential to the outer edge of a 1.41-m radius 77.5-kg grindstone (which is a solid disk). 1) What is the torque τ, in newton meters, you are exerting on the grindstone, relative to the center of mass of the grindstone? τ = 2) What is the angular acceleration of the grindstone α0, in radians per square second, assuming negligible friction? α0 = 3) What is the angular acceleration of the grindstone αf, in radians per square second, if there is an opposing frictional force of 20.5 N exerted 0.35 m from the axis? αf =
The fishing pole in the figure makes an angle of 20.0o with the horizontal. What is the torque exerted by the fish about an axisperpendicular to the page and passing through the angler’s hand if the fish pulls on the fishing line with a force of 100 N at anangle 37.0o below the horizontal? The force is applied at a point of 2.00 m from the angler’s hands.
In which of the three cases would it be easiest to calculate the torque using METHOD 2? (You may select more than one case)
Rank the pictured torques on a solid beam from most negative to most positive. The black dot in the beam is a fixed pivot axis which is located at the very end of the beam (notice that c, e, and f have different pivots!). You may assume that forces are either applied at the end or the center of the beam. Angles that appear to be 90 degrees, are 90 degrees. If torques are equal in magnitude, please indicate this. If any of the torques are zero, please indicate this.
In the following mechanism, T1 torque and F1 force act on the AB link. Equilibrium conditionSCD according to the superposition principle, the magnitude of torque required to be applied to the CB.obtain by making drawings? (F1 is vertical from mid point of ABIt is applied directly) O=40⁰, CB=3m, AB=2m
For case A of spin-the-bottle, calculate the magnitude of the torque. Assume that the applied force is 70.0 N and the size of the grid spacing is 3.20 cm. [Answer in units of Newton metres (Nm) with 3 sig figs but do not enter units with your answer]
The figure below shows forces acting at various points on a metal cylinder. The angles a = 50°, ß = 27°, y = 23°. The length { = 3.8 m. Find the net torque (in N• m) on the cylinder about the following axes. 25 N B. 10 N 30 N (a) an axis through O perpendicular to the page magnitude N: m direction ---Select--- (b) an axis through C perpendicular to the page magnitude N: m direction ---Select---
Write the necessary equation of the object shown in figure below. Fx R, go Take the origin of the torque equation about an axis perpendicular to the page through the point O. (Let counterclockwise torque be positive and let forces to the right and up be positive. Use any variable or symbol stated above along with the following as necessary: Fg for the magnitude of Fg.) ΣFx X. = 0 EFy = = 0 Στ = 0
Let r be a vector with an initial point located on the axis of rotation and with a terminal point located at the point where a force F is applied. Find the torque and explain what the torque is measuring.