Two engineering students use a steel tape to measure a base line repeatedly and the results in meters are as follows: 96.395, 96.401, 96.403, 96.399, 96.397 Choose the answer that shows the line's most probable value. O 96.401 meters O 96.399 meters O 96.400 meters 96.395 meters

Two engineering students use a steel tape to measure a base line repeatedly and the results in meters are as follows: 96.395, 96.401, 96.403, 96.399, 96.397 Choose the answer that shows the line's most probable value. O 96.401 meters O 96.399 meters O 96.400 meters 96.395 meters

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Do not include the unit in writing the answer. Express all values up to 3 decimal places. You can directly compute in your calculator and just write the formula used on your solution paper. Use capital letter in writing the station. Complete the table below. STATION BM1 AB с D E F BM2 BS 2.055 1.517 2.775 1.604 2.558 1.803 Highest elev of the line of sight Station with the highest elevation (excluding BM1 & BM2) Lowest rod reading Station with the Highest BS Lowest Elevation HI 332.276 332.467 332.955 334.776 336.036 334.894 FS 2.229 1.029 1.018 1.540 2.945 3.056 ELEV 330.047 331.438 331.937 333.172 333.478 331.838
Please answer immediately. Thank you!
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is ± 2.50% Relative to the right answer. XB: 188.419mm Xc: 471.768mm Ya: 209.808mm Ze: 155.444 mm Zf: 471.096 mm 5.) Determine the x-component of the moment experienced by the system assuming that there is no wire support. 6.) Determine the y-component of the moment experienced by the system assuming that there is no wire support. 7.) Determine the z-component of the moment experienced by the system assuming that there is no wire support. 8.) Determine the Tension experienced by the wire DF.
Please help ASAP. Rate will be given accordingly. Write the answer on the paper.
find the three
XXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX SOLVE STEP BY STEP IN DIGITAL FORMAT с XXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX D 8 XXXXXXXXXXX USING THE FIGURES AND THE DATA, CALCULATE: a). The bearings of the sides of the polygon b). The interior angles of the polygon c). Perform the sum of interior angles and verify with the geometric condition or theoretical calculation { int = 180°(n − 2) E XXXXX XXXXXX XXXXXXXXX XXXXXXXXXXXXXXXXXXX XXXXXX A E. P.O. AZIMUT Distance A B 279°40'00" 232.46 в с 221°20'00" 190.85 C D E A 131°23'00" 195.05 108°25'00" 068.54 29°30'00" 292.76 D XXXXXXXXXXXX E Headings
A line was determined to be 2,682.13 meters when measured with a 20 m. steel tape supported throughout its length under a pull of 4 kg. at a mean temperature of 39 °C. Tape used is of standard length of 19 °C under a pull of 5 kg. Cross- sectional area of the tape is 4.796 mm^2. Determine the TOTAL ERROR of the LINE due to TEMPERATURE in meters. Round off to three decimal places. Input the magnitude only.
Using any Geometric Methods only: (Double Integration, Conjugate Beam, Area Moment) Determine the deflection (mm) of the beam at point B. Round off your final answer in 2 decimal places P kN w kN/m A C B X1 EI Given: P - 30 kN w - 10 kN/m X1 m X2 200000 MPa 700 x 10 mm
Name of Friends Weight in kilogram Arianne 90 Sunshine 75 Sushi 58 Gemini 63 Eliot 88 Saskei 54 Jariw 43 Mhuxa 37 Kartana 105 Balivna 66 Ariler 82 Derite 55 Daniel 98 Kareine 40 1. Arrange the given data from lowest to highest 2. Find two values of each quantile. One lower and one upper. Show your solution. Compute for Q, and Q6, Dz and D12. P33 and Pgo
Question 39/50 Situation 39, 40 10m/s Es=200 GPa E,=105 GPa 50 kg Steel 15 mm-diaBrass k=25 kN/mm 图的的 1.5m 1.5m 0.5m O Zoom image Determine the stiffness of Spring, Steel and Brass assembly as shown. O 8256.25 N/mm O 9141.75 N/mm O 2563.23 N/mm 5632.20 N/mm PreviouIS Next >
A polygon has the following data as given in the table. Determine the adjusted measurement of its interior angles. Round-off answers to degrees-minutes. Interior Angle Ꮎ° 12345 117 98 87 150 102 Weighted Measurement 3 4 157 5 2
I need a quick solution within 15 minutes With my best wishesTon