Two distances of 50 and 80 meters were accurately measured out, and the intercepts on the staff between the outer stadia webs were 0.4% at the former distance and 0.7% at the tatter. Calculate the tacheometric constants.

Q: The following observations were taken in reciprocal levelling. Staff reading at Instrument at A B A…

A:

Q: Convert the angle 238ᵒ25’50’’ into its equivalent in decimal degrees.

A: Concept used:- 1ᵒ = 60’ (1 degree = 60 minutes) 1’ = 60’’ (1 minute= 60 seconds)

Q: The following data were obtained by stadia measurement that has internal focusing. It will be use to…

A:

Q: Now find the exact location of the centroid.

A:

Q: Given the data below, solve for the required unknowns. 1. Solve for the elevation at BM2 Station BS…

A:

Q: The transit is set up at A and a stadia vas places at a distance of 184. 20m from A. The stadia…

A:

Q: Which one is the CORRECT expression for the horizontal distance between the instrument and the staff…

A: given staff intercept = S multiplying constant= K additive constant= C D= horizontal distance

Q: LINE AZIMUTH FROM NORTH AB ВС CD DE EF

A:

Q: Given are the interior angles of a heptagon. Determine the discrepancy for the givenobservation and…

A:

Q: Define Normalized CPT Parameters

A: Cone penetration testing (CPT) is used to identify the soil type. In this test a cone penetrometer…

Q: In determining the stadia interval factor (K) of a transit, a stadia rod was held vertically at…

A:

Q: SITUATION: From the given figure. TABLE GH 003 can be useful. Determine the settlement of the clay…

A: Answer Over burden pressure σo= 100 kpa Liquid limit LL = 60% Height of clay layer H=6 m distance…

Q: A transit with stadia interval factor of 100.8 was set up at point C on the line between points A…

A:

Q: A transit with a stadia interval factor of 100.80 was set at C on the line between point A and B,…

A: Given data

Q: -670 m hi= 1.54 m 34.34 m r= 1.87 m. A

A: It is required to find the elevation of A given the elevation of B is 86.53 m Distance between A and…

Q: The angles of a triangle ABC were recorded as follows: No. of Measurements Angle Value A 77 14' 20'…

A:

Q: The transit is set up at A and a stadia was places at a distance of 184. 20m from A. The stadia…

A:

Q: Fundamentals of Surveying: Please show your solution. 7.) A line with bearing, N 77° 45' E…

A:

Q: Complete the table below. C 118°37 105°22' Sta A B C D E 108° 28' E B 120°28¹ N30°00'W MERIDIAN…

A:

Q: istance by Tachymetry 1. A stadia rod held at a distant point B is sighted by an instrument set up…

A:

Q: A lot is in the form of a regular Hexagon. If the magnetic deflection when they measured side EF is…

A:

Q: Four interior angles of a five-sided polygon traverse were observed as A = 110°4759", B =…

A: Observation Station  Interior Angle  A 110°47'59" B 121°06'12'' C 122°33'32" D 114°02'25"…

Q: Distance by Tachymetry 1. A stadia rod held at a distant point E is sighted by an instrument…

A:

Q: stadia

A: This question is from Surveying.

Q: H.W/ the following details refer to reciprocal levels taken with a level. Instrument at station…

A: In curvature, the points are lower while in refraction the points are higher than the actual. So,…

Q: ?What is the elevation of point A in the below figure, if you know that the elevation of point B is…

A: Given Elevation of point B = 92.108 m we have to find elevation of point A

Q: The magnetic bearing of line XY was observed to be S 31° W, when the declination was 2° E. Point Z…

A: Magnetic Bearing of line XY = S31°W Declination = 2°E Point Z was sighted at 20°(right)  from the Y…

Q: b) A tape 30m long of standard length a 29°C was used to measure a line the mean temp during…

A: Length of measuring tape may change due to various factors such as: Slope Temperature Sag Reduction…

Q: B: Find the elevation of point (B) from the figure (2) that showing below : Fig. (2) 1.48 m IR Elev.…

A: Draw the given figure:-

Q: Where did θ = 14.04 and 2θ = 28.08 came from? And in Rcos(28.08) why is it multiples to cos?

A: This question is already answer in attached answer.  This question is related to the Surveying…

Q: The upper, middle and lower hair reading is 2.45 m, 1.86m, and 1.27 m respectively. Determine the…

A: Determine the horizontal distance from the instrument to the the observed point.

Q: A vector, F , has components Fx=-228.2 N andFy = 155.4 N. What is the angle made with the…

A: We knowtanα=FyFxα=tan-1FyFxwhere α=angle made with x-axis horizontal

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.