Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the reaction at the left support (in kN-m).

Q: Problem #2 6m YkN/m A B The support at 4 can be assumed to be a roller. Point C is an internal…

A: As per the guideline we are supposed to answer three subparts only. Kindly repost the question for…

Q: The aluminum-alloy shaft AC has a 400-mm-long tubular section AB and an 800-mm-long solid segment…

A:

Q: 8k/ft 4 k/ft 30 ft

A:

Q: W=P=53 Solve the reactions at the support. Indicate what method is used. Please show the complete…

A:

Q: 10 kN/m 10 kN/m C 5 m D 4 m 6 m

A:

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: The beam is used to support a dead load of C kN/m, a live load of A kN/m and a concentrated live…

A: "Since you have posted a person with  multiple subparts. we will solve first three for you. To get…

Q: Find the reaction at A due to the uniform loading and the applied couple. The force reaction is…

A: Given, Cantilever Beam with UDL and moment at free end

Q: Beam determine the support reactions (solve using integral)

A: Hi student! you haven't mentioned the area expression of the load in the questions so, we are…

Q: Determine the reactions at all supports and the force transmitted through the hinge at C for the…

A: To find reaction at support

Q: supports for the beam shown. 25 kN/m В 12 m A

A:

Q: Determine the value of reaction at support E if the applied 1 unit load is on point D. Hinge. E…

A: Energy reaction power is applied to a structure when it depends on something. The analysis of the…

Q: Determine then,draw 2 k/ft the reactions on the beam. the shear-moment diagram 3 k/ft 600 k ft 12 ft…

A:

Q: 30 kN/m B A 10 m

A: Using equilibrium equation

Q: 80 kN A 1om 10m

A: Degree of Redundancy of the structure, DOR = 5-3=2 Therefore, no of redundants = 2 Taking reaction…

Q: 2. Portions AB and CD have flexural rigidity EI, and portion BC has flexural rigidity 3EI. Determine…

A: P = 30kips w = 1kips/ft [Note :equation (i) & (ii) has been added and equated to zero, due to…

Q: 45 kN 30° 7.5 kN/m A 3 m 3 m

A: Draw FBD:

Q: b) The frame is loaded and supported as shown in Figure Q4b. (1) Draw the free-body diagrams of the…

A: As per Bartleby's guidelines we are supposed to answer only first question.Kindly repost other…

Q: Determine the reactions at supports. Assume “EI” is constant. Draw the moment diagram. Select the…

A: Given:Required:Support reaction and moment diagram

Q: Problem (4) The compound beam is supported by a rocker at B and is fixed to the wall at A. If it is…

A: Question is based on the compound beam supported by a rocker at one end and other is fixed . Loading…

Q: Determine the reactions of the structure. Determine the internal forces of each element, in kN.…

A:

Q: 5. Determine the reactions at the supports A & B. see Figure 5. |5 KN /m Figure 5 t to 2.5m 20m 2-0m

A: Reaction at support A is 11.805 KN  Reaction at support B is 66.944 KN

Q: Solve the frame approximately using Portal Method. 30KN 6m k 60KN- 6m 72KN- 8m 10 m 12m 10 m 1.…

A:

Q: 3. Determine the reactions at the supports -3m- 400 N/m -3 m-

A:

Q: Determine the reactions at B, C, and the maximum force F if the reaction at A is 175 kN. Note that…

A: To find Reaction at B &C  Maximum force F

Q: Solve the support reaction at A. 6 ft A B 8 ft 8 ft E 8 ft 6 ft 30 kips C

A:

Q: Determine the reactions at the supports, A is fixed connected. E is constant .Use Force method of…

A: Shear and bending moment diagrams are analytical techniques that are used in conjunction with…

Q: What is the maximum positive moment for the beam shown? Use the method of consistent deformations.…

A:

Q: 2P. 3P 4m" 3m A= 3300 mm? E= 160 GPa P = 100KN.

A:

Q: find the reactions at a and d

A:

Q: 1 kN/m, a live load of 2 kN/m, and a concentrated live load of 52 kN. Determine the following:…

A:

Q: Determine the reactions on the beam as shown in Figure 8. A is pin and B is roller.

A: The given beam is shown below:

Q: Determine the reactions at support A and D. Assume A is a pin and B is a roller 800 lb 30° -10 ft- B…

A:

Q: how to draw the beam load for a combined one and two way slab

A: Step 1: Understand the Slab SystemOne-Way Slab: A one-way slab distributes the load to two opposite…

Q: -3 ft- 100 lb 3 ft- B 200 lb-f 2 ft 13 12. B 15 Determine the reactions on the bent rod which is…

A:

Q: The 450-kg uniform l-beam supports the load shown. Determine the reactions at the supports. -5.6 m-…

A:

Q: 3. The distributed loading acts on the simply supported beam. The support at A is a pin and the…

A: A simply supported beam with hinged support at A and roller support at B with an equal overhang of…

Q: Determine the reactions on the bent rod which is supported by a smooth surface at B and by a collar…

A: Given :

Q: 22: Determine the reactions at the supports using the force method. El is cons Take Dy as a…

A: Using strain energy method : force method

Q: Q.3 The solid steel shaft has a diameter of 20 mm. If it is subjectod to the two torques, determine…

A: Torque the amount of force that makes an object or shaft-like structure rotate about its axis.  As…

Q: . Determine . Determine .. Determine the minimum the maximum (or negative) reaction at B. positive…

A:

Q: Determine the determinacy of the given figure. Determine the reaction at A, B, C, D, and E. The…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.