Two blocks of wood 50mm wide and 20mm thick are glued together. a. Using the free body diagram concept, determine the shear load and from it the shearing stress in the glued joint if P = 6000 N. b. Generalize the procedure of part (a) to show that the shearing stress on plane Psin 20 inclined at an angle 0 to a transverse section of area is Ss %D 2A 20mm 60 P = 6000 N P = 6000 N 50mm

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: If the analysis of the forces involved on an object produces a negative answer for a force: The…

A: If doing calculation and getting any force hwith negative that means, The negative sign indicates…

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: Determine the distance and resultant of the five parallel forces acting on the rocker arm of the…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Q3: Each cord can sustain a maximum tension of 500 N, Determine the largest mass (m) of p pipe that…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Let's work through the calculations for the given L-shaped object.### Part a: Finding the x-centroid…

Q: Q3: Each cord can sustain a maximum tension of 500 N, Determine the largest mass (m) of pip that can…

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: Write the equation to calculate the work done by an axial force?

A: Work: Work is defined as the multiplication of the axial force on the body and displacement…

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: I needed it to be solved using differential equation

A:

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: Draw longitudinal cross section of the commutator and label each part.

A: Commutator and its diagram and Function.

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: choose the correct answer 200 B. G- A Zero Force members

A: We know that if a joint with two members is not subjected t any external load and also that joint…

Q: Q3/ Determine the resultant of the force system with respect to the point (A)

A:

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: Write the equation that relates applied stress to local maximum stress.

A: Stress concentration factors are generally used to relate applied stress to local maximum stresses.…

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: Maximum Stresses in Thick Walled Cylinders

A: To determine the maximum radial and tangential stress for the thick walled cylinder

Q: Q4. The compound shaft shown in Figure Q4 is attached to rigid supports. For the bronze segment AB,…

A: As per Expert Q&A guidelines we are supposed to answer the first three parts of the given…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.