Two blocks of mass ma = 10 kg and mg = 5 kg are connected by a massless string that passes over a pulley as shown in the figure. The system is in static equilibrium. There is friction between m, and the inclined surface (=0.4). Neglect the friction between the string and the pulley. Determine the static friction force in the system. 10 kg 5.0 kg 37 49.0 N 29.3 N 39.2 N 33.9 N 9.98 N

Two blocks of mass ma = 10 kg and mg = 5 kg are connected by a massless string that passes over a pulley as shown in the figure. The system is in static equilibrium. There is friction between m, and the inclined surface (=0.4). Neglect the friction between the string and the pulley. Determine the static friction force in the system. 10 kg 5.0 kg 37 49.0 N 29.3 N 39.2 N 33.9 N 9.98 N

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter5: Displacement And Force In Two Dimensions

Section: Chapter Questions

Problem 82A

See similar textbooks

Similar questions

There are four forces acting on a pole, A = 10i N, B = 20j N, C = -30j N, D = -40i N. What should be the magnitude of force E that must be exerted on the pole to maintain static equilibrium? Note: i and j are unit vectors a. 24.65 N b. 31.62 N c. 46.20 N d. 52.78 N e. No Answer
63. To find the resultant of a concurrent force system, express each force as a Cartesian vector and add the i, j. k components of all the forces in the system. True False 64. A position vector ir ates one point in space relative to another point. True False 65. The tensile force developed in a continuous cable that passed over a frictionless pulley must have a constant magnitude throughout the cable to keep it in equilibrium. O True False 66. A cable can support only a compressive or "pulling" force. True False 67. In equilibrium, IF includes all the known and unknown forces which act on the particle. True O False
A 60.0 cm, uniform, 50.0 N shelf is supported horizontally by two vertical wires attached to the sloping ceiling (Eigure 1). A very small 25.0 N tool is placed on the shelf midway between the points where the wires are attached to it. Figure 25.0 cm Tool 75.0 cm 20.0 cm 1 of 1 Part A Find the tension in the left-hand wire. Express your answer with the appropriate units. T = Value Submit Part B Request Answer Find the tension in the right-hand wire. Express your answer with the appropriate units. TR= Value Submit Units N Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining ?
A bridge of length 50.0 m and mass 8.10 x 104 kg is supported on a smooth pier at each end as shown in the figure below. A truck of mass 2.90 x 104 kg is located 15.0 m from one end. What are the forces on the bridge at the points of support? AM. A, В 15.0 m 50.0 m normal force at point A normal force at point B N Need Help? Read It Master It
A uniform plank of length 2.00 m and mass 29.0 kg is supported by three ropes, as indicated by the blue vectors in the figure below. Find the tension in each rope when a 705-N person is d = 0.500 m from the left end. magnitude of T, 493.56 378 Your response differs from the correct answer by more than 10%, Double check your calculations. N 671.95 Your response differs from the correct answer by more than 10%, Double check your calculations. N magnitude of T. magnitude of T, 40.0° -2.00 m
A 16-lb force is being applied to end D of arm BCD. The arm is connected by pins to crank AB at point B, and to a frictionless collar at point C. Determine the couple M required to hold the system in equilibrium when 0 = 90°. Include both the magnitude and direction of couple M as part of your answer. 10 in.→ 12 in.→ В 7.5 in. 8 in. M. 6 in. 16 lb The solution to this problem requires a free-body diagram for each member of the machine, and a sketch of the coordinate system used. Use the components of the forces with EF, = 0 and EF, = 0 to apply EF = 0 for a member. %3D y
what is the magnitude of the resultant force acting on the pin and the angle between the resultant force and its x component. refer to the figure shown below. choices are a. R = 83.62 N , angle 6.05 b. R = 143.09 N , angle 9.79 c. R = 63.84 N , angle 3.26 d. R = 103.32 N , angle 7.78 e. R = 123.19 N , angle 8.95
A uniform spool is suspended from a vertical wall by a string attached to the spool’s thin axle. The axle is horizontal, as shown below. The wall is smooth, so it exerts no frictional force on the spool. The tension in the string is 2.6 N. What is the weight of the spool? a 1.2 N b 1.0 N c 0.5 N d 2.4 N e 2.6 N
The end of a light rope ABCD are connected to the same horizontal beam at A and D. Masses of 1 kg are suspended at B and C. AB = CD BC and AD = 2 AB. Calculate the tension in each part of the rope using the method of components if A and D are in the same horizontal plane (use g = 9.81 m/s2). A.
2.750 m A square metal plate with mass M = 5. 80 [kg] and side length 2. 75 [m] is pivoted about an axis through point O at its zenter and perpendicular to the plate. Three forces of magnitude F1 = 40.0 [N], F2 = 48. 0 [N], and F3 = 36. O (N] act on the plate as shown. Л. What is the nettorque on the square plate due to these forces? 45° What is the angular acce eration of the diski The moment of inertia for a plate of length a and width b rotating about its center is I com = M(a? + b?). 12 C. If the plate is initially at rest, what is the angular velocity of the particle after 3.00 [s]? 2.750 m B.
A string, having a diameter of 1 mm and density of 16.0 x 103 kg/m³, is fixed at one end. Its other end hangs over a pulley and has a block of mass 2.00 kg attached to it, as shown in Figure 2. L O OA. 23.5 N OB. 13.3 N OC. 19.6 N O D. 16.2 N m Figure 2 The horizontal part has a length L = 1.60 m and a mass m = 20.0 g. Calculate the tension in the string. B
Vector Forces and Resultant 1. A 10.0 kg mass hangs from two strings, each making an angle of 35.0° with the ceiling. What is the tension in each string? 2. Two children are sitting on a seesaw of a uniform board with a fulcrum on its center of mass. One child (m=30kg) is 2.0m to the left of the fulcrum. Where should the second child (m=50kg) sit so that they are in equilibrium?