Two blocks are being pushed along an incline. Block A weighs 7.00 kg and block B weighs 14.00 kg. The coefficient of non-sliding friction between block B and the surface of the incline is 0.200 and the coefficient of sliding friction is 0.1000. Assume that the coefficient of friction between the two blocks are too high to cause sliding between the two blocks. The applied force is 185 N. 185 N 40°

Two blocks are being pushed along an incline. Block A weighs 7.00 kg and block B weighs 14.00 kg. The coefficient of non-sliding friction between block B and the surface of the incline is 0.200 and the coefficient of sliding friction is 0.1000. Assume that the coefficient of friction between the two blocks are too high to cause sliding between the two blocks. The applied force is 185 N. 185 N 40°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 13.21 The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F= (3000t2) N, where t is in seconds. (Figure 1) Figure 1 of 1 ₁ = 2 m/s wh T Part A If the car has an initial velocity ₁ = 2m/s at s = 0 and t = 0, determine the distance the plane when t = 3 s. Express your answer to three significant figures and include the appropriate units. S = O D Submit |μA Value Units My Answers Give Up ? Provide Feedback moves up Continue
11.7 (A/B). A solid shaft carrying a flywheel of mass 100 kg and radius of gyration 0.4m rotates at a uniform speed of 75 rev/min. During service, a bearing 3 m from the flywheel suddenly seizes producing a fixation of the shaft at this point. Neglecting the inertia of the shaft itself determine the necessary shaft diameter if the instantaneous shear stress produced in the shaft does not exceed 180 MN/m². For the shaft material G= 80 GN/m². Assume all kinetic energy of the shaft is taken up as strain energy without any losses. [22.7 mm.]
The coefficient of static friction for both wedge surfaces is 0.34 and that between the 34-kg concrete block and the 25° incline is 0.66. Determine the minimum value of the force P required to begin moving the block up the incline. Neglect the weight of the wedge. P 3.7 Answer: P = 34 kg 25° N
Two blocks are joined by an inextensible cable with a force P- 1,500 N applied to block B as shown. If the system is released from rest, determine the velocity of block A after it has moved 3 m giving that mA - 100 kg, ma-200 kg and the kinetie friction coefficient is 0.30. Conservalion f Serga
k=2 lb/ft -¨¨¨¨¨ B Two blocks A and B have a weight of 11 lb and 6 lb, respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.23. Determine the angle 0 which will cause motion of one of the blocks. What is the friction force under each of the blocks when this occurs? The spring has a stiffness of k = 2 lb/ft and is originally unstretched. Determine the smallest angle which will cause motion of one of the blocks. Determine is the friction force under the block A at this angle. Determine is the friction force under the block Bat this angle.
3. Determine if the tractor which has a weight of 8000 lb with center of gravity at G, can push the 550-lb log up the incline. The coefficient of static friction between the log and the ground is 0.5, and between the rear wheels of the tractor and the ground 0.8. The front wheels are free to roll. Assume the engine can develop enough torque to cause the rear wheels to slip. 1.25 ft B 2.5 ft |10° 3 ft -7 ft
SITUATION. An 8-m long ladder weighing 900 N is shown in the figure. It is required to determine the horizontal force P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. BN W = 900 N %3D B, 4m 4.59m 2 m 35° A, AN 6.55m Determine the required force P. B.
kN per cubic meter and water weighs 9,790 N per cubic meter. Coefficient of The section of a concrete dam is shown in the figure. Concrete weights 23.5 friction between the dam and foundation is 0.55. Determine the factors o head at the heel of the dam to zero at the toe. Consider 1 m length of dam. Problem 3 - 108 kN per safety against sliding and against overturning, and also the soil heel and toe. Assume hydrostatic uplift varies uniformly from full hydros bead at the heel of the dam to zero at the toe. Consider 1 m of pressure at the length of dam. Ans: FSo = 2.20; FSs 1.66 Theel = 85.2 kPa; qtoe %3D 300.2 kPa
Q1:A reinforced concrete tank * has a bottom plate (foundation) which assumed to be sliding (hinge), find the magnitude that used for drawing the Tangential Force, and then find maximum shear force, using the following data: Diameter (D) =9014mm, Height (H)=8000mm, Thickness (t)=335mm,Poisson ratio (v)=0.25, yw=10KN/m3=1x10-5 N/ mm3
2.0 ft 2.0 ft Determine the magnitude of Pfor which slipping impends, provided h is within the range where it does not cause tipping. a 270 lb b 135 lb c 540 lb d 315 lb If the magnitude of Pis 250 Ib determine height h a 4.44 ft which tipping impends. b 2.40 ft W = 600 lb c 3.00 ft d 4.80 ft Hs = 0.45
100 lb In the fig. shown, compute the minimum Weight W to prevent impending motion of the block up the incline. The weight of the block is 100 lb as shown and the coefficient of friction between the block and the incline u = 0.45. Assume frictionless pulley. 450