Two 6-in.-wide wooden boards are to be joined bysplice plates that will be fully glued onto the contact surfaces, asshown in Figure 2 . The glue to be used can safely provide ashear strength of 120 psi. Determine the smallest allowable lengthL that can be used for the splice plates for an applied load of P =10,000 lb. Note that a gap of 0,5 in. is required between boards (1)and (2).(1)(2)0.5 in.-FIGURE 2

Given:width,w=6 inshear strength,ζ=120 psiApplied force,P=10,000 lbGap=0.5 inArea of contact between…

Answered: Two 6-in.-wide wooden boards are to be…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 1: Three vertical posts AD, BE, and CF are held between two horizontal rigid plates. Posts AD and CF are made of steel (Es = 200 GPa) and have cross sectional areas of 1000 mm² each. Post BE is made of aluminum (Ea = 73.1 GPa) and has a cross sectional area of 1500 mm². Initially, there is a small gap of 0.1 mm between BE and the top horizontal plate. Then a vertical force of P = 410 kN is applied, which is more than sufficient to close the gap completely. D -0.5 m B E -0.5 m- 0.4 m F Determine the normal stresses in posts AD, BE, and CF (both magnitude and sign).
15° An actuator applies a force to a cable to hold the blade in place while the table holding the CheezeT drops away. The cable is redirected over a stationary drum. Determine the maximum load on the actuator and choose a material for the drum (explain your choice). (25 points) Concrete: us=0.5 Teflon: us=0.1 Cheeze Table
Cylinders 1 and 2 are glued as shown in the figure. The tensile strength of the glue is 24 MPa, its shear strength is 18 MPa. The glue is evenly distributed over the cylinder with a diameter of 30 mm and an unknown length L. The force F supported by the assembly is 2,600 daN. Calculate the minimum length L to give to the glued joint of the assembly.
1. The given structure, shown in Figure 1, is composed of two beams with a rectangular profile b x h, attached by a pin. The member having length lz is loaded by a vertical force F acting at the mid-point of the member. (a) Calculate the magnitude of the force that can be safely applied to the structure without the loss of stability of the structure during the operation. (b) Write down the steps that you need to perform, including diagrams and symbolical equations needed, to confirm that the magnitude of the force F, computed in section 1a, will not cause a plastic deformation on the beams. Consider oyield =270MPA Note: Your work must be accompanied by a clearly labelled diagrams l1 = 1 m d = 2 m a = 60° F E = 210 GPa %3D b = 15 mm h = 25 mm 1/2 Figure 1
A simply supported reinforced concrete beam carries a uniformly distributed load of 12 kN/m on a span of 4 m. The beam has a rectangular cross section 250 mm wide by 450 mm deep, with three 20 mm diameter steel bars placed 60 mm from the bottom of the beam, as shown below. The moduli of elasticity for the concrete and steel are 15 GPa and 200 GPa, respectively. Determine the average tensile stress in the steel and the maximum compressive stress in the concrete at the section of maximum bending moment. 450 mm 250 mm 60 mm
Part A The bolted connection (Figure 1) joins the bar supporting force P to two flanges set into a wall at A and B. In addition to supporting the load transferred by the bolt, the flanges are also subjected to additional 5-kN and 2-kN loads, as shown. Determine the largest internal shear force resisted by the bolt when P= 8 kN. (Figure 1) Express your answer to three significant figures and include appropriate units. Value Units Submit Request Answer Part B Determine the largest internal shear force resisted by the bolt when P = 23 kN and P = 18.6 kN. (Figure 2) Express your answer to three significant figures and include appropriate units. Value Units Figure Submit Request Answer SAN Provide Feedback Next > 2kN
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?
For 10 to 12. The compound bar ABCD has a uniform cross-sectional area of 0.25 in². When the axial force P is applied, the length of the bar is reduced by 0.018 in. The moduli of elasticity are 29 x 106 psi for steel and 10 x 10 psi for aluminum. 18 in. 6 in. 18 in. P. P Steel B C Steel D -Aluminum 10. What is p? 11. What is the total elongation of the two steel sections? 12. What is the elongation of the aluminum section?
4. The bar below is subjected to an axial load of P. The safety factor against compressive failure is 1.5. Find the allowable load in KIPS if the material is cast iron. Sin 2in 1 ft
1. Steel rod 2.5m long is secured between tow walls. If the load on the rod is zero at 200C, compute the stress when temperature drops to (-200C). The cross-sectional area of the rod is 1200 mm2 α=11.7μ m/(m.0C) and E=200 GPa. Solve assuming (a) that the wall is rigid and (b) that the wall spring together a total distance of 0.500mm as the temperature drops. 2. The rigid bar ABC in Figure is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the aluminum rod if the temperature of the steel rod is decreased by 40°C. Neglect the weight of bar ABC.
Two columns are of equal length, equal supporting conditions, made of the same material, but of different cross section as shown in the image below. The cross sections are equal in area but different in shape: one is square and the other is rectangular. Columns are loaded with a comprehensive force. Which of the following statements is true about whether one column or the other can be subjected to a greater force with buckling? A. Both columns have equal critical force as their cross sections are equal in area. B. The column of the rectangular cross section is stronger against buckling. C. The column of the square cross section is stronger against buckling. D. Buckling is not possible for such structures. E. None of the above.
(13) A spring has an overall length of 44.0in & sustains a load of 15,000lb @ its center. The spring has three full-length leaves & 15 graduated leaves with a central band 4.0in wide. All leaves are to be stressed to 60,000psi when fully loaded. The ratio of total spring depth to width is to be approximately 2.0. Determine: (a) the width & thick ness of the leaves; (b) the initial space that must be provided between the full length & the graduated leaves before the band is applied; (c) What load is exerted on the band after the spring is assembled?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS