a11¹0+Ts/1ipX_xRlwUUPZvncHq13mHcMJkmGPPvb_Tutorial 7(41 X 64GTransformers1Question 1A 600 kVA single-phase transformer with a turns ratio of 3300:380 and a rated primaryvoltage of 3300 V has a total series equivalent impedance referred to the primary (HV)winding of 1,07477.53° 2. If the transformer is to deliver its rated kVA to a load connectedto its secondary winding with a secondary voltage equal to 380 V and with the load powerfactor equal to 0,7 lagging, calculate the voltage that must be applied to the primary winding.C

Tutorial 7 Question 1 Transformers A 600 kVA single-phase transformer with a turns ratio of 3300:380 and a rated primary voltage of 3300 V has a total series equivalent impedance referred to the primary (HV) winding of 1,07277,53° 2. If the transformer is to deliver its rated kVA to a load connected to its secondary winding with a secondary voltage equal to 380 V and with the load power factor equal to 0,7 lagging, calculate the voltage that must be applied to the primary winding.

Tutorial 7 Question 1 Transformers A 600 kVA single-phase transformer with a turns ratio of 3300:380 and a rated primary voltage of 3300 V has a total series equivalent impedance referred to the primary (HV) winding of 1,07277,53° 2. If the transformer is to deliver its rated kVA to a load connected to its secondary winding with a secondary voltage equal to 380 V and with the load power factor equal to 0,7 lagging, calculate the voltage that must be applied to the primary winding.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 200 MVA 15/200 kV single-phase power transformer has a resistance of 2.40 and a reactance of 10.012 referred to the high voltage side. The voltage regulation of this transformer for the secondary winding current of 1100A at PF of 0.8 lagging is a. 5% b. 4.01% C. 3.8%
A 16 kVA, 58Hz, single - phase transformer has a turns ratio of 14: 2 and is supplied from a 2.7 kV supply. Neglecting losses, determine (a) the secondary voltage, (b) the full load primary current, (c) the maximum flux and (d) the minimum value of load resistance which can be connected across the secondary winding without the kVA rating being exceeded .
A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b
13)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.
2.Fringing effect is a phenomena occurs in .. (a)Transformers. (bElectrical field. (e)Air gap (d)All of the above. 3, The kVA rating of an ordinary 2-winding transformer is increased when connected as an autotransformer because (@ transformation ratio is increased (b) secondary voltage is increased (c) energy is transferred both inductively and conductivity (d) secondary current is increased. 4. The .... of the hysteresis loop is a measure of energy lost per cycle (a) area. (b) Туре. (c) Frequency (d) No one of the above. 5. At relatively light loads, transformer efficiency is low because (a) secondary output is low (b transformer losses are high (c) fixed loss is high in proportion to the output (d) Cu loss is small. 6. In an ideal transformer, (a) windings have no resistance (b) core has no losses (c) core has infinite permeability (d) all of the above. 7. In electromagnetic circuits, path of eddy current is.... (a) Parallel to the path of the flux. (b) Perpendicular to the path of…
A 10 kVA, single-phase transformer has a turns ratio of 12:1 and is supplied from a 2.4 kV supply. Neglecting losses, determine (a) the full load secondary current, (b) the minimum value of load resistance which can be connected across the secondary winding without the kVA rating being exceeded, and (c) the primary current.
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
In a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220, then the percentage regulation is 4.54%. Select one: True False
The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W. Round your answer off to the nearest whole number
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.