Transmission line of Zo = 75 0 and electrical length (= 0.333A is terminated with a Z = 30-j40 N.Find(i)the reflection coefficient at the load ( r),(ii)VSWR,(iii) the input impedance to the line Zin-

(i) The reflection coefficient at the load is given by the expression as shown below: τ0=ZL-Z0ZL+Z0…

Transmission line of Zo = 75 Q and electrical length (= 0.333A is terminated with a Z = 30-j40 N. Find the reflection coefficient at the load ( I), (ii) VSWR, (iii) the input impedance to the line Zin- (i)

Transmission line of Zo = 75 Q and electrical length (= 0.333A is terminated with a Z = 30-j40 N. Find the reflection coefficient at the load ( I), (ii) VSWR, (iii) the input impedance to the line Zin- (i)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A lossless transmission line has a capacitance per unit length of 90 uF/m (microFarad/meter) and an…

A: Lossless transmission line A transmission line with no line resistance and no dielectric loss is…

Q: Determine the voltage standing wave ratio VSWR, the reflection coefficient I'and the line return…

Q: 18. The reflection coefficient for the I transmission line shown in figure at P is Transmission line…

A: In the question, What is value of reflection coefficient of the given transmission line.

Q: For a frequency of 100 MHz, a transmission line with characteristic impedance Z-100+j50 is…

A: Given, A transmission line with, Characteristic impedance, Z0=100+j50. Load impedance, ZL=50+j100.

Q: A lossless transmission line has a characteristic impedance of 100 and is loaded by 100 + j100 N. A…

Q: tic impedanc by load 7 =1

A: The characteristics impedance is independent of the length of the line. Now, this voltage and…

Q: Derive the expression for total inductance of a transmission line.

A: Inductance of a transmission line is calculated as Inductance=Flux linkagesCurrent passing through…

Q: Q2: Give the one method to arrest the Standing Wave Ratio and reduce the reflection Coefficient to…

A: Method to arrest standing wave ratio The most intuitive method uses a slotted line which is a…

Q: impedance 48-j54 N. Using Smith Chart calculate the following: i. VSWR ii. ii. Load Admittance YL.

A: Given that Z0=60 ohmZL=48-j54 ohm Although reflection co-efficient is given by Voltage reflection…

Q: a) Determine the impedance seen from point A, due only to Z_L. You can do it in the form analytical…

Q: 2. The reflection coefficient of a load is L=0.8. Determine: (a) VSWR

A: Given: Reflection coefficient of a load, ΓL=0.8.

Q: A 502 transmission line is terminated with a 502 resistor on series with a 2 * 10 7H inductor. If…

Q: 32) Bypass diodes are MOST often located in which PV system component? O Ihverters O Modules O…

Q: The characteristic impedance of a transmission line is 70 ohms and has a load of 35 ohms. The SWR…

A: The solution is given below

Q: 2. A transmission line with Zo = 1000 and 1 = 0.42 is terminated with a Z₁ = 30+ j500 load. The…

A: The objective of the question is to find the reflection coefficient at the load and the standing…

Q: Problem 2: Given that the voltage standing-wave ratio S = 3 on a 50 O line, that the first voltage…

Q: For the circuit shown in figure 1: By using Smith Chart, compute: 1. The impedance at the length…

A: Given, the circuit The 0.1λ length line shown has a characteristic impedance of 50 and isterminated…

Q: 2. The phasor voltage on a terminated transmission line is given by 1 -e-j2nz + +j2nz What is the…

Q: How can you use a vector network analyser to measure frequency when the characteristic impedance is…

A: A precise electronic test tool called a "Vector Network Analyzer" (VNA) examines the amplitude and…

Q: A 702 high-frequency lossless line is used at a frequency where 2 = 80cm with a load of 140+j91 2 a.…

Q: ). A transmission line has a characteristic impedance of 502 and a resistance of 0.1 Q/m. If the…

Q: Normalized admittance values zL= 0.4 - j0.3 with two load impedances connected in parallel with a 50…

A: To find the distance of voltage maxima and minima, we need to first calculate the wavelength of the…

Q: Design a quarter wave matching section if the line has a characteristic impedance of 100 ohm while…

A: Given

Q: What can we eliminate negative parts of an AC signal, with and without using offset

A: Eliminate the negative part of the ac signal without using offset voltage Using a positive clamper…

Q: b. Determine what is the necessary length and characteristic impedance of a cable to be used as a…

Q: A transmission line i terminated by a load with admittance Y- (0s- j08)IZ Find the normalized input…

A: A transmission line i terminated by a load with admittance Y=(0s- j08) Find the normalized input…

Q: ® Find IN, ZH and IL for ZLOAD 230V 2-3') LOMD 344;

A: In this question, We need to determine the Norton equivalent and load current as shown in the…

Q: wave for T-L Connected to th Bo Example 5 Find the impedance and standing Load ZR as a) ZR 23 Zo__b)…

A: Step-1-> a) ZR=3Zo when ZR = 3Zo, the impedance seen at the load is 3 times the characteristic…

Q: at 20 MHz the characteristic impedance of a transmission line is (20-j2) ohm and the propagation…

A: Given, Frequency (f) = 20 MHz Characteristic impedance of a transmission line, Zo = 20 - j 2 ohm…

Q: 500 transmission line is terminated with a 500 resistor on series with a 2 * 10 H inductor. If the…

Q: 0.35λ long with characteristic impedance Z0= 50 ohms transmission line is combined with ZL=10+j25…

A: Smith chart:It is a graphical tool used in RF (Radio Frequency) for analyzing and designing…

Q: H. W., discuss how we can use the PN generator in the transmitter (Tx) and receiver (Rx) circuits…

A: Transmitter : A transmitter is an electrical device that generates radio waves in order to…

Question

Transmission line of Zo = 75 0 and electrical length (= 0.333A is terminated with a Z = 30-j40 N.
Find
(i)
the reflection coefficient at the load ( r),
(ii)
VSWR,
(iii) the input impedance to the line Zin-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Transmission Line Parameter and Scattering Parameter (S-parameter)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

On distortionless line, the voltage wave is given by 12010025 Los (10 t +21²) + 60 e -100251 Ve 6 " Cos (10² taze) where I' is the distance from the load. Assuming Z₁₂=3005², find a- 2, B, u b) Zo and Illit).
5- Analyze the synchronous counter shown in Figure 2. Construct the state diagram to show the counting sequence of the counter. B A High J Q Clock O CK CK СК K Q K Q K Q Figure 2
A 60-2 transmission line is connected to a 75-2 resistive load. If the incident voltage is 5 V rms, then the reflected voltage is: a) -1.026 Vrms. b) -0.832 Vrms. c) 0.556 Vrms. d) 1.569 Vrms. e) 2.320 Vrms.
Q4) A- For the following SWR Pattern, find the reflection coefficient of the load and Ag . -8.6 43 - mm.i- 80. Bo 140 B- Draw the SWR pattern for a matched load, comment on that pattern.
Q-1) Polystyrenes has a relative permittivity of 2.7. If the wavw is incident at an angle 'ei' of 30° from air onto polystyrene, the angle of transmission will be nearly..?
Blue is the numerical answer, I need a detailed solution.
7
A transmission line of characteristic impedance of Zo=50 ohm with length of A/4 loaded by a load impedance of 150ohm find 1- the load reflection coefficient 2- the standing wave ratio (SWR)
b) If quantity A is PATAT with TC of 2mV/C, and quantity B is CTAT with TC of -1mVrC, then determine the following quantities if they are PTAT or CTAT 1. 1/A 2. 1/B 3. A+ 5°B
Transmission Lines (i). (ii). What is transmission line and why we can study it using periodic configuration of LC circuits? What is characteristic impedance and why it is important? Do you know any practical example of its use? (ii). Explain the difference between open and short circuit at the end?
!EMERGENCY! Normalized admittance values zI= 0.4 - j0.3 with two load impedances connected in parallel with a 50 cm long coaxial line insulated with dielectric (€1 = 3) It is connected to a source with an operating frequency of 1 GHz. Find the distance of the voltage max and min to the load and the normalized input impedance of the line.
For a T.L. of Zo=50 Ohm, terminated with ZL= 100 Ohm, the value of the VSWR is: O 2 O 3