ZAIN IDA traffic light is installed at ajunction of a railroad and aroad of cars. The traffic light iscontrolled by two switches inthe rail placed one mile aparton either side of the junction.A switch is turned on when thetrain is over it and is turned offotherwise. When thebeginning of the train is onemile from the junction, thetraffic light is changed fromgreen (logic "O") to red (logic"1"). The light is changed backto green when the end of thetrain is one mile away from thejunction and S1 is turned off.Assume that the length of thetrain is less than two miles. Thecircuit diagram of theaforementioned state machineincludes . SR-flip flop(s). *Imile1mile

SUMMARY: - Hence, we discussed all the points.

traffic light is changed from green (logic "O") to red (logic "1"). The light is changed back to green when the end of the train is one mile away from the junction and S1 is turned off. Assume that the length of the train is less than two miles. The circuit diagram of the

traffic light is changed from green (logic "O") to red (logic "1"). The light is changed back to green when the end of the train is one mile away from the junction and S1 is turned off. Assume that the length of the train is less than two miles. The circuit diagram of the

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter2: Problem Solving Using C++using

Section2.1: Introduction To C++

Problem 9E: (Practice) You’re given the task of wiring and installing lights in your attic. Determine a set of...

See similar textbooks

Similar questions

2. Develop a ladder program for following system: PB 1 is used for main system ON. PB 2 is used Main OFF. Lights will be switched on and off with following sequence. Lights White light Action Switch ON for 30 second when sensor 1 is sensed Red light Green light Orange light Yellow light Switch ON for 1minute when sensor 2 is sensed Switch ON for 2 minute when sensor 3 is sensed Switch ON when no sensors are sensed Switch ON when all sensors are sensed
Consider a thermostat with only one temperature threshold. In the initial state, if the temperature is less than or equal to 20 degrees Celsius, it turns the heater on and leaves it on for at least 30 seconds. After that, if the temperature is greater than 20 degrees, it turns the heater off and leaves it off for at least 2 minutes. It turns it on again only if the temperature is less than or equal to 20 degrees. Design an FSM that behaves as described, assuming it reacts exactly once every 30 seconds
What is the resolution of the timing procedure clock() and gettimeofday()?
1. A water sprinkler system operates based on the input of a set of pumps and a set of sensors. The water sprinkler is ON if both pump set and sensor set are ON. • The set of pumps consists of two pumps. If one of the pumps is ON, the set of pump is considered ON The set of sensos consists of three sensors. The set of sensors is considered ON if sensor 1 and sensor 2 are both ON, while sensor 3 must be OFF. Develop the logic gate and Boolean equation for the pressing machine operation. Include relevant truth tables to support your answer. 2. A safe deposit room in bank has a safety door. The safety door can be locked automatically by sensors or manually by security personnel. The sensors are activated when: • The laser beam circuit is OPEN or the weight sensor circuit on the floor is CLOSED. The camera detects moving object. Develop the logic gate and Boolean equation for the pressing machine operation. Include relevant truth tables to support your answer.
Assertion (A):Wien bridge can be used for measuring frequency Reason (R):A frequency meter for 50 Hz system has a frequency range of 40 to 60 Hz • Both A and R are true but R is not correct explanation of A • A is false R is true • A is true Ris false • Both A and R are true and R is correct explanation of A
R-2000 2 An electrical capacitor with an unknown capacitance is connected to the circuit shown. The switch is first connected to B and the capacitor is charged. Then, the switch is connected to A and the capacitor discharges through the resistor. As the capacitor is discharging, the voltage across the capacitor is measured for 10 s in intervals of 1 s. The recorded measurements are given in the table below. Vo | 3| 4 | 5 | 3.55 2.81 6 7 1.26 | 2 8 10 V(V) | 9.4. 7.31 | 5.15 2.04 0.97 0.74 | 0.58 You recall from PHYS2102 that the voltage of the capacitor, during a discharge, as function of time is given by V = V, e*t/(RC) This exponential equation can be written as a linear equation of In(V) and t in the form : In(V) = t + In(V6) Use Matlah to do the following: "In all graphs add title, sgend and axis labels 1. Estimate the time at which the voltage V = 6.5 V. 2. Estimate, using spline interpolation, the voltage V1 corresponding to 30 times varying from 1 to RC 10s. 3. In the same…
You need to program the logic for an autonomous road line painting vehicle. The vehicle (flashes yellow hazard lights during operation) is responsi a solid yellow line when the road bend is 45 degrees or more. When the road curvature is straight (or less than 45), a white dashed line must be pa intersection, the painting must stop and resume once past the intersection. When the vehicle reaches the final destination or at any time, should th deplete, the vehicle must stop and the red hazard lights must be turned on. Write down the procedure for a computer to perform this task as well-written pseudo-code. Your pseudo-code must be explicitly stated in low-level could be easily translated into a computer program by a programmer.
A factory produces two types of wood blocks with 2m and 4m lengths. The blocks are moved by a conveyor belt and passing under two photocells A and B spaced by 3m apart as shown in the following figure. The blocks are separated by more than 4m. A trap door is placed immediately to the right of photocell B. To separate the two types of blocks, it is required that the trap door should open when the small block pass under Band close when the blocks passed beyond B. The door opens when the output (2) of state machine is logic 1. The designer needs for . AND-gate(s) for implementing the aforementioned state machine (2) a d> 4m 3m 0.25m
Two methods for flow control are stop-and-wait and sliding window. Distinguish the differences between them in terms of frame transmission.
Asap
The line through (-2,-5) and (1,9). The line through (3,7) and (-11,10).
Which Al-controlled computations are more likely? unconstrained Al?