draw top and isometric view

Q: For the body shown. If point P3 is the center of mass for rod part P1-P2, and point P4 is the center…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: State if the flow represented by u = 3x + 4y and v= 2x – 3y is rotational or irrotational. [Ans.…

A:

Q: If block B is moving downwards with a speed of 2 m/s at the instant shown, Determine the speed of…

A:

Q: 4. Without using any software, write a G-code programme to produce the part shown in Figure 2. Take…

A: N0 G90 F0.5 S1200 T0101 M03N10 G00 X35 Z2N30 G71 U0.5 R1N35 G71 P36 Q90 U0.05 W0.05N36 G01 X20 Z0N50…

Q: find the top view, right side view, front view and the figure (isometric/oblique drawing)

A: Given:- Front and side view of a part Scale=10mm   To find:- To draw Front view, Right side view,…

Q: Draw isometric view

A:

Q: 2) A car travels along a circular road with aradius of curvature of 75 m, and velocity of 10 m/s.…

A: Given Acceleration at 15 m  can be determined as

Q: A duct is being used to transport propane at a temperature of 25 °C. Part A Estimate the maximum…

A:

Q: orthographic view (software drawn)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: The 500MB jet airliner has three engines. each of which produces a nearly constant thrust of 250 kN…

A:

Q: Weight of the refrigerator is 880 N. The coefficient of static friction is 0.22 for all surfaces.…

A:

Q: a stone is thrown vertically from a 100 ft tower with initial velocity = 50 ft/ sec ,at the %3D same…

A:

Q: Q13) Cars A and B are travelling around the circular race track. At the instant shown. A has a speed…

A:

Q: Two identical pendulums, each with mass m and length I, are connected by a spring of stiff- ness k…

A:

Q: The 800-1b cylinder is supported by three chains as shown. Take d = 1 ft. (Figure 1) Figure < 1 of 1…

A: Here, co-ordinates of points are, A(0,0,-1), B(1cos1350,-1cos1350,0)=B(-0.707,0.707,0)…

Q: It is observed that the skier leaves the ramp A at an angle OA = 30 degrees with the horizontal and…

A: Given data  VA = 21.8 m/s θA = 30 degrees g = 9.81 m/s2 To determine  a) Time of flight (tA-B) b)…

Q: Task 2.2 A large pressure vessel contains air in state 1 (pi = 3 bar, T1 = 360 K, c1 = 0 m/s). The…

A: Given: At state 1p1=3 barT1=360 Kc1=0 m/sηsD=0.9State 2:p2=1 barA2=0.1 m2

Q: Draw isometric view then complete the top view

A:

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: The 4-kg collar is attached to a spring that has an unstretched length of 2m and a stiffness k=10.1…

A: Given: The mass of the collar is, m=4 kg. The unstretched length of the spring is, l=2 m. The…

Q: A100 kg boy starts from rest at the bottom A of a 10-percent incline and increases his sneed at a…

A:

Q: sketch the development

A: the given is isometric view

Q: Sketch the othographic  Isometric and  Any other if so draw of the following sketch  ( Use…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: GIVEN: ISOMETRIC PICTORIAL VIEW. SKETCH (1) LEFT SIDE VIEW. THEN SKETCH FRONT AND TOP VIEWS.

A: The orthographic projection of the 3 dimensional object will give the 2 D view of the object. The…

Q: Draw the sectional view.

A: According the given view we need to draw the isometric view. i am using solid works to draw…

Q: For the body shown. At the instant shown, point B moves in straight line in y positive directi with…

A: There are two types of accelerations that are acting on a circular surface. One type of acceleration…

Q: Redraw multiview to an isometric sketch

A: Find Draw the multiview of the object.

Q: Draw top view and sectional view(s)

A: Find Draw a top view and sectional view of the given object. Note: Some dimensions are not clearly…

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.