The 800-1b cylinder is supported by three chains as shown. Take d = 1 ft. (Figure 1) Figure < 1 of 1 Part A Determine the force in AB chain for equilibrium. Express your answer to two significant figures and include the appropriate units. FAB= μA Value Part B Units Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Determine the force in AC chain for equilibrium. ?

Q: colour the hatchinga and create the 2d sketch and give different colors to the refernce line and…

A:

Q: Assume the below given figure as unit length to be equal to 10 mm, draw the isometric views of…

A:

Q: not read the answer. Is there a way to upload it in ano

A: Navier-stokes equation (momentum and continuity equations)

Q: A satellite is launched from earth such that the booster burnout occurs at an altitude of 422 km…

A: Given data: Burnout occurs at an altitude, h=422 km Velocity, vo=9.5 km/s=9500 m/s, Flight path…

Q: Determine the location of the sweet spot of the bat shown in the figure (Figure 1). The linear mass…

A:

Q: The given system of forces is, F2 F3 m

A:

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: Can you make it for me?(image below)just screenshot the result after you make the shape on the…

A: Given 3D model To find  View

Q: Please do not give solution in image format thanku

A: The physical explanation for why rubber's Young's modulus is lower than steels is found in how these…

Q: Given FRONT AND SIDE VIEW sketch the Top or bottom view NOTE

A:

Q: A satellite is launched with the following conditions: Tovi = 1, Bo = 20° where ro, vo, Bo denote…

A:

Q: PART-A (Sectional View - SKETCHING) 1. Reproduce all two views given and add/complete the sectional…

A: Given Diagram To find Sectional views

Q: For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the…

A:

Q: An overhead view of part of a pinball game is shown. If the plunger imparts an initial speed of 3.3…

A:

Q: de (h) To make the ride more exciting it is proposed that the wheel should ascend in such a way that…

A: Given: Diameter of the wheel: →D=100 m Total time taken for a complete revolution: →T=15 min=900 sec…

Q: I need help answering these two parts pertaining to the print provided below.   For this drawing,…

A: Note: We are authorized to answer one question at a time. Since you have asked three questions at…

Q: A particle which moves in two-dimensional curvilinear motion has coordinates in millimeters which…

A:

Q: Determine the location h of the spot toward which the pitcher must throw if the ball is to hit the…

A: given velocity v= 38.5 m/sec

Q: Sketch the orthographic view Top Side and Front Using engineering graphics drafting

A:

Q: Given TOP VIEW & FRONT VIEW sketch the side view and isometric view Note : Assume each unit as 10 mm

A:

Q: If the compact disc is spinning at a constant angular rate 0 = 355 rev/min, determine the magnitudes…

A:

Q: PART-A (Sectional View - SKETCHING)1. Reproduce all two views given and add/complete the sectional…

A: Given Object To find Views

Q: Sketch an object that contains all of the necessary elements so that you can use the following line…

A:

Q: The given picture shows the following parts of a blower. Please state its functions and discuss how…

A: Write the parts of blower. (1) Motor (2) Impeller (3) Blades (4) Casing

Q: mechanical engineering : engineering drawing : AutoCAD Can someone please show step by step…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: GIVEN: ISOMETRIC PICTORIAL VIEW. SKETCH (1) LEFT SIDE VIEW. THEN SKETCH FRONT AND TOP VIEWS.

A: The orthographic projection of the 3 dimensional object will give the 2 D view of the object. The…

Q: Below are incomplete views of the parts Complete them if necessary. NB: Let the lines of…

A: Note: As per the policy, we can solve the first question from the multiple questions. Please,…

Q: FOR THE FOLLOWING FIGURES ISOMETRIC VIEW IS NEEDED  Sketch theisometric view using the below…

A:

Q: Given the two views of a multiview drawing of an object, sketch the missing top view on paper.…

A: Given view  Front and side view  Missing view : top view

Q: prepare and submit an oblique drawing based on the 2D Multiview object drawing.

A: We get an oblique view or oblique projection by taking 45° from the side

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.