To determine the organic material in a dried lake bed, the percent carbon by mass is measured at two different locations. To compare the means of the two different locations, it must first be determined whether the standard deviations of the two locations are different. For each location, calculate the standard deviation and report it with two significant figures. location 1 standard deviation: location 2 standard deviation: What is the calculated F value for comparing the standard deviations? Feale = Sample 1 2 no O yes 3 4 5 Location 1 (% Location 2 (2 C) C) 10.40 10.10 10.30 10.90 10.30 10.30 10.40 10.80 10.20 10.40 Are the standard deviations for the two locations significantly different at the 95% confidence level?

To determine the organic material in a dried lake bed, the percent carbon by mass is measured at two different locations. To compare the means of the two different locations, it must first be determined whether the standard deviations of the two locations are different. For each location, calculate the standard deviation and report it with two significant figures. location 1 standard deviation: location 2 standard deviation: What is the calculated F value for comparing the standard deviations? Feale = Sample 1 2 no O yes 3 4 5 Location 1 (% Location 2 (2 C) C) 10.40 10.10 10.30 10.90 10.30 10.30 10.40 10.80 10.20 10.40 Are the standard deviations for the two locations significantly different at the 95% confidence level?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

4. Two technicians have analyzed a standard with a known nitrate concentration of 25.0 mg/L. The results are shown below. Results from Technician 1 (mg/mL) Results from Technician 2 (mg/mL) 23.4 23.8 TO 23.2 Trial 1 2 3 4 5 23.4 22.9 23.6 Average: 23.4 30.1 22.4 27.5 21.3 Average: 24.9 Choose the statement below which is FALSE. a. Technician 2 has greater accuracy than technician 1. b. Technician 1 has greater precision than technician 2. c. Results from technician 1 have both systematic and random error. d. Results from technician 2 only have determinant error.
A student determines the concentration of an unknown sample using two different methods. Each method has three different trials; the average, standard deviation, and percent error produced by each method is listed below. Method 1 Average: 10.56 M NaOH Standard deviation: 1.35 M NaOH Percent error: 1.25% Method 2 Average: 10.92 M NaOH Standard deviation: 1.02 M NaOH Percent error: 3.45% Which method was more accurate? How can you tell?
Use a spreadsheet to calculate the mean and standard deviation of the data set. 54.99, 54.40, 54.60, 54.63, 54.36 The figure shows a suggested setup for your spreadsheet, where you enter the data in the highlighted cells and enter formulas in cells C4:D8 and B9:B11 to carry out the appropriate calculations. mean: standard deviation:
Provide the correct IUPAC name for CaSO₄. and for Provide the correct IUPAC name for Ca(NO₃)₂
The following volumes were obtained for the calibration of a 10 - mL pipet: 10.028415, 10.140035, 10.091111, and 10.012213 mL. Calculate the mean value, the standard deviation and then report your value.
1
The standard solution is prepared by dissolving a known mass of zinc pellets with conc. HCl. The solution is then neutralized, transferred into a 250 mL volumetric flask and filled to the calibration mark. If 0.9809 g of Zn was weighed using an electronic balance with a relative uncertainty of ± 0.01 % and the 250 mL volumetric flask has a known relative uncertainty of ± 0.06 %, what would be the absolute uncertainty of the concentration of the solution? The molecular weight of the zinc pellets is 65.39 g/mol
The following volumes of 0.000300 M SCN are diluted to 15.00 mL. Determine the concentration of SCN in each sample after dilution. These values will be used during the experiment. To enter exponential values, use the format 1.0e-5. Sample 0.000300 M SCN (mL) [SCN'] (M) 1 1.50 3.50 7.00 4 10.00 3.
In a particular trial, a student got a value for R of 0.083. Calculate the percent deviation of this result. Enter a number without the % sign. The percent deviation should be reported as a positive value.
3. A chemist used two different methods to measure the number of mg of Fe in five iron(II) sulfate supplement tablets. The results of each are shown below. 64.71mg Method 1: 65.03mg 61.55mg 64.9 mg 65.1 mg Method 2: 65.5 mg 66.1mg Calculate the average amount determined by each method as well as the standard deviation and RSD for each method. 63.07mg 65.4mg 67.15mg Which method gave more precise results? How do you know? Is it possible to know which method is more accurate? Why or why not?
chips trial mass of the chip mass of the fat %by mass of fat regular 1 20.043 6.745 33.65% 2 20.187 6.438 31.89% 3 20.198 7.451 36.89% lowfat 1 19.456 3.982 20.47% 2 20.072 4.547 22.65% 3 20.192 4.589 22.73% Calculate the average % by mass of fat for each type of chip. Show your work.
Dr. Caras was characterizing a cytochrome (an iron containing protein) from a new strain of bacteria. He obtained eight measurements of the percent iron in the protein: 0.2409%, 0.2404%, 0.2394%, 0.2399%, 0.2515%, 0.2393%, 0.2409%, and 0.2392%. Calculate the mean (x) and standard deviation (s) for these results. % S = Use the Grubbs test to determine if one of these values is an outlier. What is the value of Galculated? Gcalculated = Should this potential outlier be rejected with 95% confidence? Critical values of G can be found in this table. The potential outlier should be rejected. The potential outlier should be kept.