to cluding just the first few program to plot the sum the series. (c) Repeat v L'= L+S, (11.54) (b) The maximum magnitude of L' occurs when L and Sy are parallel. By taking the z component of (11.54) and remembering that the maximum value of L is lh (and similarly for all angular momenta), show that the maximum possible value of I' is I + 1. Show similarly that the minimum possible value is l- 1. This leaves only three possibilities, I' = +1 or l or l– 1, and Problem 11.26 has shown that l' = l is not allowed, so you're home. 11.35 (Section 11.4) Do lem 11.34 for the sam using the triangular v (b) plot just the first te ... 11.36 (Section 11.5) Co 11.22, which is initially finite square well with field & is switched or function picks up a sr x42(x). (a) Use a sui plots of 2(x) and xu mediately clear what (multiplied by a sma this, expand x2(x) a cients Am of this expa that, to a good appro: has the form x2(x) right-hand side of th with your plot of x %3D SECTION 11.10 (Further Properties of Lasers*) 11.32 A single-mode He-Ne laser has a beam of diameter 3 mm. As the beam propagates away from the laser, its diameter increases because of diffraction. (a) Given that this effect simply adds to the initial beam size, find the distance at which the beam diameter is doubled. (b) At what distance will the beam have a diameter of 1 m? * Recall that the spin enters the energy through the term -u B, which involves the magnetic field, and that the effects of B are usually negligible compared to those of &. cance of this result? A single-mode 3 mm has an angular divergence lim prot imate diameter of the beam at a distance of 300 m. By what factor is the According to (11.47), 80 A/d; therefore, as shown in Fig. 11.15, the tion of a mict0second. still present and again e spike. This process com that which can make N intensity reduced at this distance? radius R of the beam at a distance L is eam at a LA ately Q-Switching The size of the pulses fication begins as soc N N. Larger pulsa fore laser amplificatie fication temporarily This method of prod name originates in th R L 80 beam size. r) With L 300 m, this gives (300 m) x (6.3 x 10-7 m) R 3= 3 x 10 m 60 mm Therefore, the beam diameter is about 120 mm. Since intensity is power per unit area, it is inversely proportional to the cross-sectional area of the beam. Thus the ratio of final to initial intensities is rameter is a measur before it dies away." ample) slowly and h small, the light loses does not occur. (4) 2. I1 md/4 d 1 22 1600 In the lasers di low-loss mirrors am achieved. This caus the size of the puls This loss of intensity is sufficiently large that it must obviously be taken into account when planning to use lasers over large distances.

to cluding just the first few program to plot the sum the series. (c) Repeat v L'= L+S, (11.54) (b) The maximum magnitude of L' occurs when L and Sy are parallel. By taking the z component of (11.54) and remembering that the maximum value of L is lh (and similarly for all angular momenta), show that the maximum possible value of I' is I + 1. Show similarly that the minimum possible value is l- 1. This leaves only three possibilities, I' = +1 or l or l– 1, and Problem 11.26 has shown that l' = l is not allowed, so you're home. 11.35 (Section 11.4) Do lem 11.34 for the sam using the triangular v (b) plot just the first te ... 11.36 (Section 11.5) Co 11.22, which is initially finite square well with field & is switched or function picks up a sr x42(x). (a) Use a sui plots of 2(x) and xu mediately clear what (multiplied by a sma this, expand x2(x) a cients Am of this expa that, to a good appro: has the form x2(x) right-hand side of th with your plot of x %3D SECTION 11.10 (Further Properties of Lasers) 11.32 A single-mode He-Ne laser has a beam of diameter 3 mm. As the beam propagates away from the laser, its diameter increases because of diffraction. (a) Given that this effect simply adds to the initial beam size, find the distance at which the beam diameter is doubled. (b) At what distance will the beam have a diameter of 1 m? Recall that the spin enters the energy through the term -u B, which involves the magnetic field, and that the effects of B are usually negligible compared to those of &. cance of this result? A single-mode 3 mm has an angular divergence lim prot imate diameter of the beam at a distance of 300 m. By what factor is the According to (11.47), 80 A/d; therefore, as shown in Fig. 11.15, the tion of a mict0second. still present and again e spike. This process com that which can make N intensity reduced at this distance? radius R of the beam at a distance L is eam at a LA ately Q-Switching The size of the pulses fication begins as soc N N. Larger pulsa fore laser amplificatie fication temporarily This method of prod name originates in th R L 80 beam size. r) With L 300 m, this gives (300 m) x (6.3 x 10-7 m) R 3= 3 x 10 m 60 mm Therefore, the beam diameter is about 120 mm. Since intensity is power per unit area, it is inversely proportional to the cross-sectional area of the beam. Thus the ratio of final to initial intensities is rameter is a measur before it dies away." ample) slowly and h small, the light loses does not occur. (4) 2. I1 md/4 d 1 22 1600 In the lasers di low-loss mirrors am achieved. This caus the size of the puls This loss of intensity is sufficiently large that it must obviously be taken into account when planning to use lasers over large distances.