Title A transmitting valve is cooled by water circulating through its hollow electrodes. The water enters. Description A transmitting valve is cooled by water circulating through its hollow electrodes. The water enters the valve at 25°C and leaves it at 85°C. Calculate the rate of flow in kg/ second needed per kW of cooling. The temperature of 1 kg of water is raised to 1°C by 4178 joules.

Title A transmitting valve is cooled by water circulating through its hollow electrodes. The water enters. Description A transmitting valve is cooled by water circulating through its hollow electrodes. The water enters the valve at 25°C and leaves it at 85°C. Calculate the rate of flow in kg/ second needed per kW of cooling. The temperature of 1 kg of water is raised to 1°C by 4178 joules.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The time for 1 cycle is 5 micro second. Find the frequency. a. 1500 Hz b. 1500 kHz c. 200 kHz d. 200,000 kHz
16. The reactance of 0.106 Henry is connected to a 110-volt, 60-cycle source. Calculate a. The inductive reactance b. The current in the circuit C. The average power taken by the inductor and the maximum power delivered to the inductor
The reactance of 0.106 Henry is connected to a 110 – volt, 60 – cycle source. Calculate: (a) the inductive reactance, (b) the current in the circuit, (c) the average power taken by the inductor, (d) the maximum power delivered to the inductor. INCLUDE PHASOR DIAGRAM IF POSSIBLE ROUND OFF TO FOUR DECIMAL PLACES
The armature of a 60 Hz ac generator rotates in a 0.45 T B-field. The area of the coils is 0.06 m2. a. Determine what the current & power output (not the power loss) will be if the resistance of the coil is 0.2 Ω. I = 850 AP = ?
once. Force Completion This test can be saved and resumed at any point until time has expired. The timer will continue to run if you leave the test. Remaining Time: 34 minutes, 38 seconds. * Question Completion Status: A Moving to another question will save this response. uestion 1 What is the maximum recommended limit of RMS voltage (in percent) for continuous operation of shunt capacitors under contingency condition? O 110 120 130 135 A Moving to another question will save this response. 直 0 a hp
6. The time for 1 cycle is 5 micro second. Find the frequency. a. 1500 Hz b. 1500 kHz C. 200 kHz d. 200,000 kHz C.
6) In a pulse laser micro-welding process, the pulse energy is 6 J. Pulse on time is 4 ms. Calculate the peak power and pulse off time of the system if the pulse frequency is 20 Hz. a. 1500 KW and 4.6 s b. 1500 W and 46 ms c. 150 W and 460 ms d. 1500 kW and 460 ms
c) A linear sensor-transmitter is used in the flow control loop. The current transmitter output is at 8 mA when the flowrate in the pipeline is 5 m³/hr. Calculate the gain of the sensor- transmitter if the lowest value of the calibrated flow sensor is 0 m³/hr. Determine the range of the calibrated flow sensor.
(b) Figure Q2(b) represents a single-line diagram of typical power system with the line impedances as indicated in pu on a 100 MVA base with a synchronous generator at Bus 1. The line charging susceptances are neglected. Calculate the bus voltages of V½ and V3 in pu using Gauss-Seidel method with the initial estimates of V, = 1+ j0 pu and V) = 1+ j0 pu. Perform only THREE (3) iterations. (0) (0) 1 230.5 0.01+j0.03 pu MW G 0.025+j0.05 pu 0.02+j0.04 pu 172.9 MVAR V1 = 1.0620°
can you explain the difference when I changed the number of winds from 10 to 100? elaborate
The meter constant of a 245 volt, 70 ampere, single phase energy meter is 1650 revolutions per KWh When tested at quarter load, rated voltage and 0.8 power factor, the meter is found to make 100 revolutions in 65 seconds. Determine the percentage error at quarter load
A.C. with a frequency of 60 Hz. If the maximum value of the current is 120 amperes, write the equation for its instantaneous value. Calculate the time from when the value of the current rises from zero to positive (i) the value of the instantaneous current after 1/720 second and (2) the time for the value of the current to become 103.9 amperes for the first time.