Three solid cylindrical rods are welded together to form the compound axial member shown in Figure P5.4. The compound axial member is attached to a fixed support at A. Each rod has an elastic modulus of E = 40 GPa. Use the following values for the rod lengths and areas: L1 = 1,440 mm, L2 = 1,680 mm, L3 = 1,200 mm, A = 260 mm², A2 = 130 mm², and A3 = 65 mm². What magnitude of external load P is needed to displace end D a distance of upD= 60 mm to the right? %3D %3D %3D %3D %3D

Three solid cylindrical rods are welded together to form the compound axial member shown in Figure P5.4. The compound axial member is attached to a fixed support at A. Each rod has an elastic modulus of E = 40 GPa. Use the following values for the rod lengths and areas: L1 = 1,440 mm, L2 = 1,680 mm, L3 = 1,200 mm, A = 260 mm², A2 = 130 mm², and A3 = 65 mm². What magnitude of external load P is needed to displace end D a distance of upD= 60 mm to the right? %3D %3D %3D %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, however, a gap of A = 0.25 in. exists between the two pipes. Bronze pipe (1) has an elastic modulus of E, = 16,000 ksi, a cross-sectional area of A, = 2.83 in.?, and a length of L1 = 6.9 ft. Aluminum alloy pipe (2) has an elastic modulus of E2 = 10,000 ksi, a cross-sectional area of A2 = 1.47 in.2, and a length of L2 = 12.0 ft. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses produced in each of the members. (b) the final position of flange B with respect to support A. L2 В (1) Answer: (a) σ1- ksi 02 = ksi (b) OB/A = in.
Answer the problem question and store value and then use 4 decimal places as final answer then box the final answer. Don’t forget the unit. Take note: Write it on a paper, hand written showing correct answer.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
b. Discuss how the figure below and determine the rigid bar BDE as used to support by two link AB and CD. 0.4 m 0.3 m B D 0.4 m 30 kN E 0.2 m The Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm2. Link CD is made of steel (E = 200 GPa) and has a cross- sectional area of (600 mm2). For the 30-kN force shown, determine the deflection a) of B, b) of D, and c) of E.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
In the given system rod lengths are LAB = 5m, LBc=3m and the angle attached to the horizontal of the AB rod is a = 37°. The cross- sectional areas of the rods are A = 15 cm’and Anc = 20 cm and the modulus of elasticities of the rods are E=80 GPa and EBc=100 GPa LAB , A AB Luc, Apc В C a) Calculate the stresses that will occur in the bars. 20 kN b) Calculate the horizontal and vertical displacement at point B.
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁