Three-Hinged Arch. The tied three-hinged arch is subjected to the loading shown in Figure 2. a. What are the horizontal and vertical components of the reaction at A in KN? b. What are the horizontal and vertical components of the reaction at C in KN? c. What is the tension in the cable connected to support A in KN? Figure 2 15 kN 0.5 m m 2 m- 10 kN -1 m-

Three-Hinged Arch. The tied three-hinged arch is subjected to the loading shown in Figure 2. a. What are the horizontal and vertical components of the reaction at A in KN? b. What are the horizontal and vertical components of the reaction at C in KN? c. What is the tension in the cable connected to support A in KN? Figure 2 15 kN 0.5 m m 2 m- 10 kN -1 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part C Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of d-68.0 with the floor and rope segment CD creates an angle with the horizontal. If both ropes BCA and CD can support a maximum tensile force To 140 lb, what is the maximum weight Was of the crate that the system can support? What is the angle @ required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. ▸ View Available Hint(s) VG ΑΣΦ. Η νοο ?
The hanging structure in the figure below is homogeneous. Its weight (40 kg) is acting at the center of the rectangular slab, parallel with the z-axis. Determine the magnitude (in N) of the force acting along the cable at point D. A 500 40 kg y C. 250 550 750 -550-
1. From the structure shown. a. Solve for the tensile force acting on the cables. b. Solve for the shear at 4 m from the hinged support. 30 5 m 6 m 50 kN 150 kN/m
A 2.0 kN bar AB carries a load F = 75 kN vertical force at A. The baris supported by a pin at B and the 12.5-mm. diameter cable CD. Find the a.tension in the cable CD in kN.b.Horizontal reaction at B in kN.c.Vertical reaction at B in kN.d.Tensile stress in the cable in MPa.e.Shearing stress at B in MPa.
2m Wall supported by pins at B and a roller at с • Determine the reaction at B and C • use method of joints to determine the force in each member of Wall, state whether each in Compression or tension. member is in Compression or 4.6KN 1. 4m S 2.3m 4.4 KN D
Three HInged Arch
P3/4 6. The two blocks are placed on the inclined with the cable taut. Determine the force P required to initiate motion of the 15 kg block if P is applied down the inclined. H₂=0.3 8 kg H₁ = 0.25 15 kg P 25⁰
The electric power transmission tower supports two wires that apply 18 kN verticalforces, and the 36 kN horizontal force crudely models wind loading during astorm. Assume that the supports in A and B are hinge support and roller support,respectively. Solve for support reactions.
Determine the vertical reaction, in KN, at support A for the three hinged arch shown in the figure. 40 KN 40 KN 20 KN 15KN 30 KH 30 KH G-Hinge 20m 30 m 20m* 20 m t. 20m 20m 20m 20m
Q2(a) For the semicircle arch of radius 6 m as shown in Figure Q2(a), analyse the reactions at supports A and C, and hinge B. [y = (4hx)/L*] 12 kN 4 kN/m 6 m 3 m 3 m B 6 m 8. Figure Q2(a) (b) Cable ABCD supports the loading as shown in Figure Q2(b). Analyse the vertical force at point B. 2 m 6 m 3 m 4 m B 1m 10 kN