Three forces act on the ring. The resultant force FR has a magnitude of 115 N and direction as shown, (Figure 1) F1 has magnitude 100 N and F2 has magnitude 100 N. Determine the magnitude of force F3. Express your answer with the appropriate units. HA F3 = Value Units Submit My Answers Give Up Part B Determine the coordinate direction angles of force F3. Enter your answers separated by commas. vec ? a3. B3. 73 Figure 1 v of 1 Submit My Answers Give Up Provide Feedback Co F, 45 30

Three forces act on the ring. The resultant force FR has a magnitude of 115 N and direction as shown, (Figure 1) F1 has magnitude 100 N and F2 has magnitude 100 N. Determine the magnitude of force F3. Express your answer with the appropriate units. HA F3 = Value Units Submit My Answers Give Up Part B Determine the coordinate direction angles of force F3. Enter your answers separated by commas. vec ? a3. B3. 73 Figure 1 v of 1 Submit My Answers Give Up Provide Feedback Co F, 45 30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE ANSWER ALL OF THE GIVEN QUESTIONS. Choose from the given choices/options below the question. I will rate you with “UPVOTE/LIKE” if you answer all of the questions. I will rate you with “DOWNVOTE/DISLIKE”, if you don’t answer all of the questions. THANK YOU FOR YOUR HELP.
Please answer all becuase they are all connected! UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic material having a tensile and compressive yield stress of o,, determine the following: Given: Allowable Stress = 300 MPa a = 20 mm b = 250 mm c = 250 mm This is already answered in bartleby but please recheck. Thanks a. Calculate the moment of inertia I, in x10 mm4 (If your answer is 667,335 x10 mm, then type 667.335) b. Calculate the yield moment of the section in kN.m. c. Calculate the plastic moment of the section in kN.m d.Calculate the shape factor of the section.
to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches
I keep getting 5.9 which is wrong, please help with correct answer. Thank You
solve show full solution
Please help. Written on paper not typed on computer or keyboard please. Need help on both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Q1/B) Match between Column A & B. A B A Good toughness Cutting Fluids HSS B vacuum Serrated or segmented chips Vertical shaper C Horizontal milling machining D vibration E Ductile material machined at low cutting speed Milling Chip load F Interrupted cutting operation G Emulsified Oils continuous Chip with BUE Slitting HCyclical formation of alternating high shear strain followed by low shear strain 1 Slotter Electron beam machining 10 Ultrasonic machining J Feed per cutter tooth 2 Ō88 L9GAGN 3 9 Answer from A
Please answer the given question and show the solution. Thank you very much! Note: Please include the units in the solution and use 4 decimals point in Final Answer.
Please show all the steps, thanks
5 and 6 both question must. Dont attempt partially.
QUESTION 4 needs to be answered,
DONT MIND THE BIG NUMBER ON THE RIGHT, IT IS JUST FOR NUMBERING. MAKE SURE IT IS CORRECT AND TYPEWRITTEN TO GET AN UPVOTE. NO UPVOTE IF IT IS HANDWRITTEN. THANK YOU