Three bamboo poles anchored at points B, C, and D on the ground supports the TV antenna placed at their other end at Point A. The TV antenna with anegligible weight is subjected to a wind load equivalent to a force in the component form shown in the figure.(-45î + 45k)N(0,8,0)A(0,0,-12)(-6,0,2.4)(0,0,0)..(8,0,4) 1. Which of the following shows the most ideally constructed force diagram of point A, the point where the three poles are attached to the antenna?(-45î + 45k)N(-45î + 45k)N(0,8,0),ATAD(0,8,0)A TADDTAB(0,0,-12)T0,0,-12)(0,0,0)(-6,0,2.4)(0,0,0)(-6,0,2.4)(8,0,4)(8,0,4)ВA(-45î + 45k)N(0,8,0),A TAD(-45î + 45k)N(0,8,0)A TADDTABT0,0,-12)DTAB0,0,-12)B(0,0,0)(-6,0,2.4)(0,0,0)(-6,0,2.4)(8,0,4)D(8,0,4)

The most ideally constructed force diagram of point A is

Three bamboo poles anchored at points B, C, and D on the ground supports the TV antenna placed at their other end at Point A. The TV antenna with a negligible weight is subjected to a wind load equivalent to a force in the component form shown in the figure.

Three bamboo poles anchored at points B, C, and D on the ground supports the TV antenna placed at their other end at Point A. The TV antenna with a negligible weight is subjected to a wind load equivalent to a force in the component form shown in the figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. 2 m 4 m 6 m B y Answer: Calculate the magnitude of the tension in cable BD in kN. Answer: Calculate the magnitude of the force in member BC in kN. Answer: Determine the magnitude of the moment of P about the x-axis in Nm. Answer: Determine the magnitude of the moment of P about the y-axis in Nm. Answer: Determine the magnitude of the moment of P about the z-axis in Nm. Answer: Determine the magnitude of the moment of P about the origin (point O) in Nm. Answer: (2 m
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 11j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. m 4 m 6 m B y 3 m 6 m (2 m
HW-2Dmom-02 (1).pdf Question 2. The 2D truss shown in the figure below is loaded with two forces F₁ 40 N and F₂ = 50 N. Compute the resultant of the forces R and moment of the system of forces at point A for three values of a 30°, 45°, and 90°: = 0.6 m 0.4 m Y₁ 1 / 2 + 159% + 0.6 m α 1.2 m F₂ X = 0.7 m
E Share O Zoom D Slideshow I Draw 보 Edit O Rotate Aframe of two members (A) and (BD) are connected together at pin B. The other ends are pin-supported at A and at D as shown in the figure below. A horizontal force of 500 N is applied on member (AC) at point C. The vertical component ofreaction at pin D is: 500N
Free body diagram (FBD) 30 3 kN 2m - 2 m 1.5 m 45° 8 kN-m
The following figure shows a hollow piston of weight W=50 N and diameter D=3d occupies the position initial displayed. The lateral tube has a diameter d₁=d/2. Find the descent of the piston for the equilibrium position. (b=12 cm, d=8 cm, y=104 N/m³). TBL Agua D d₁
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
Problem # 2 A weight W = 300# is suspended by a cable system as shown in the figure. a. Calculate the moment of force W with 6' respect to point D (that means with respect to an axis normal to the through D). b. Determine all cable forces and the force in paper that goes post BE. W=300 # Hint: Draw two different FBD’s for points B and C, and solve separately. What is the magnitude of the resultant of tensions in cables BC and CD? Can you figure calculation? Bonus this out without any 07
6
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 18i - 15j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN.
The Straw Hat crew on their journey to Laugh Tale Island found a big treasure box (W). Luffy wanted to place the treasure box (W) as shown in the figure. A 100-mm x 300 mm rectangular beam is supported in a horizontal position. At point "A", it is being held by a pin and at "B" by a cable BD inclined 3 vertical to 4 horizontal. Assume all forces are applied to the beam along its central axis. Given that Fcparallel to grain = 10.50 MPa, W = 79 kN and E = 13800 MPa. Neglecting the weight of the beam and cable, determine whether the design is safe. Cable 2.4 m 2.4 m
Two street lights are mounted as shown in the figure one at A and the other at C. The member AD is able to freely rotate about D. Member BE is a steel cable. B. EACH street light has a mass of 5 kg, AB=20cm, BC=20cm, CD=10cm, DE=17.32cm. Assume gravity is 9.81 N/kg. h=4cm Draw the shear force profile (a) between point A and D. On the diagram, clear indicate the values on the diagram. (b) member just to the right of point B. Calculate the maximum bending shear stress. At what distance from the bottom does it occur? Consider a cross-section of the (c) distance from the bottom does the minimum bending shear stress occur? What is its value? For the same cross-section, at what