The barge shown supports the loads wi and w2. Whatis the length of the barge L so that the upwardpressure q is uniform? For this problem, take wi =145 kN/m, w2 = 290 kN/m, L1 = 3 m, L2 = 6 m, andL3 = 3 m.- L3-BCDE

Answered: Image /qna-images/answer/620b4862-2919-4f66-8edc-6fe69928f9ff.jpg

Answered: The barge shown supports the loads wi…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Awnser
The bent rod is supported by a ball-and-socket joint at B and the cables attached to points A and C as shown in the figure. The cable at C is in z-direction. The rod is subjected to two forces, F applied at C and P applied at D. Force P is along line AD. Determine the tensions in the two cables, the magnitude of force P, and the components of the support reaction at B. 100 F = {-20i+30j} N 400 300 Dimensions in mm
Construct the reduced stiffiness matrix of the shown truss, Fig. 3.Then determine the nodal displacements and the nodal forces in clement 3. L(1) L(2) 2 m, L(3) 2/2, A(1)- A(2) = A(3) = 80 mm2, and E= 200 GPa. |1 (1) 2 2 kN '3 kN (2) 45° (3) 3 Fig. 3
For the frame shown in the below Figure, determine the horizontal and vertical components of the hinge force at B as it acts upon member AC.
The 400-kg precast concrete section is hoisted by a vertical force 'T' from a crane. Find the tension in cables AB, AC, AD.
Find the reactions at D and B ..Take F1=200 N,F2=175 N, F3=150N, M=28 N.m, * FI F2 85mm- 75 mm F3 D. V125 N -100 mm- 150 mm 50 mm 1 Add File
Need an answer for the magnitude of the tension force at cable DA asap. Many thanks!
Some idiot created the three-legged table shown. X = 0 X = l W Which of the which of the legs supports about half of the table's weight? O The far leg O The left leg None. Each supports close to one-third of the table's weight. O The right leg None. Each supports approximately the entire tabe's weight.
Find the weight of WB necessary to hold WC in the position shown, given:WC = 250 N, θ = 20 °, Φ = 10 °, x,y,h = 4,3,5, respectively
A ladder with a length of L= 8 m and a mass of M=50 kg rests on a rough ground (providing friction) and on a roller without friction at the top of the wall at h= 5 m above the ground (see figure). The angle θin the picture is 60°, and the ladder is just about to slip. (A) Draw a force diagram whichshows all forces acting on the ladder.Take the force that the roller exerts to be perpendicular to the ladder. (B) Use a net torque equation to calculate the force that the roller exerts on the ladder. (C) Use net force equations to calculate the normal from the ground, the force of static friction, and the coefficient of static friction.
A lifeboat hangs from two ship’s davits, asshown in the figure. A pin of diameter d = 0.80 in.passes through each davit and supports two pulleys,one on each side of the davit.Cables attached to the lifeboat pass over the pulleysand wind around winches that raise and lowerthe lifeboat. The lower parts of the cables are verticaland the upper parts make an angle α =15° with thehorizontal. The allowable tensile force in each cableis 1800 lb, and the allowable shear stress in the pinsis 4000 psi. If the lifeboat weighs 1500 lb, what is the maximumweight that can be carried in the lifeboat?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The barge shown supports the loads wi and w2. What is the length of the barge L so that the upward pressure q is uniform? For this problem, take wi = 145 kN/m, w2 = 290 kN/m, L1 = 3 m, L2 = 6 m, and L3 = 3 m. - L3- B C D E