Problem 3. Momentum Equations.This "double" nozzle discharges water at 10°C, (Ph2o = 1000 ) into the atmosphere at a rate of 0.50m^3 /s. If the nozzle is lying in a horizontal plane, what x-component of force acting through the flangein each jet to be the same. Jet A isbolts is required to hold the nozzle in place? Note: Assume irrotational flow, and assume the water speed12 cm in diameter, jet B is20 cm in diameter, and thepipe is31 cm in diameter.30Figure 3. Problem 3 Illustration.

Given data, Water is discharge to the atmosphere means that total flow rate through A and B, i.e.,…

This "double" nozzle discharges water at 10°C, (Ph2o = 1000 ) into the atmosphere at a rate of 0.50 m^3 /s. If the nozzle is lying in a horizontal plane, what x-component of force acting through the flange bolts is required to hold the nozzle in place? Note: Assume irrotational flow, and assume the water speed in each jet to be the same. Jet A is pipe is 12 cm in diameter, jet B is 20 cm in diameter, and the 31 cm in diameter.

This "double" nozzle discharges water at 10°C, (Ph2o = 1000 ) into the atmosphere at a rate of 0.50 m^3 /s. If the nozzle is lying in a horizontal plane, what x-component of force acting through the flange bolts is required to hold the nozzle in place? Note: Assume irrotational flow, and assume the water speed in each jet to be the same. Jet A is pipe is 12 cm in diameter, jet B is 20 cm in diameter, and the 31 cm in diameter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: QUESTION 1 A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of…

A: Note: All parts solved

Q: Problem 4 A partly full water tank admits water at 85 N/s weight flow while ejecting water on the…

Q: QUESTION 4 Water is discharged from the impeller of a centrifugal pump against a pressure of 10.5 m…

Q: A pump delivers gasoline at 20 degrees Celsius and 12 (m^3)/h. At the inlet p1=100 kPa, z1=1 m, and…

A: given flow rate, Q=12m3/hr=123600m3/sinlet pressure, P1=100Kpadistance from datum at inlet,…

Q: A frictionless convergent-divergent channel is used to accelerate the airflow emanating from the…

Q: A siphon pipe of diameter 250 mm contracts to a diameter of 100 mm over a vertical distance of 5 m…

Q: The rotor rotates at a constant angular velocity of w-130 rad/sec. although the fluid initially…

A: Turbine: The turbine is a work producing device. The energy of the working fluid at inlet of the…

Q: Water is passing through a vertical nozzle.The flow rate is 40kg/s and the cross section area at the…

A: Given: The mass flow rate, m = 40 kg/s The area of nozzle at inlet, A1 = 149 cm2 The area of nozzle…

Q: If the velocity in a 300-mm pipe is 0.50 m/s, what is the velocity in a 75-mm-diameter jet issuing…

Q: Q5: A converging-diverging nozzle, which is shown in the figure, is supplied with air from a large…

A: Given: The converging-diverging nozzle with inlet pressure Po.

Q: QUESTION 1 A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A tank (contains a fluid of density=2370.7 kg/m3) stands on a frictionless cart (The cart is fixed)…

Q: For the sprinkler shown, find a. the torque required to hold it steady, and b. the rotation rate in…

Q: The system shown in the figure is used for painting in factory. The speed of the paint that enters…

A: Given data: a = 6 and b =2 Speed of the paint, u = 1(ab) = 1(12) = 12 m/s Density, ρ = 8(ab) = 84…

Q: Calculate the power output from the turbine if the turbine efficiency is 75% and velocity at the…

A: Given:Efficiency of turbine,η=0.75V2=3 m/sZ1=50 mZ2=30 mdiameter of nozzle, d=50 mm

Q: The impacting jet for a Pelton turbine carries a flow of 0.5 m/s, and the jet is 7 cm in diameter.…

A: Given : Q = 0.5 m3/s d = 7 cm To find : Pressure of the fluid on impeller

Q: Question 2: A Pelton wheel turbine is used in a hydroelectric plant to generate electric power. In…

A: The velocity diagram for the symmetrical blade of a Pelton wheel is given below,

Q: A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from…

A: Given:Px=pressure at surface=0Vx=velocity at free surface=0A=0.01 m2zx=2 m

Q: The water (density =1000 kg/m3) leaves the nozzle (area of the nozzle=0.01 m). Assuming steady,…

Q: As seen in the figure above, the water is directed downward in the installation with a 25 ° angle…

A: (a) Write the formula for discharge to calculate the velocity at section 1 in the given figure.…

Q: Problem 3: Control Volumes When a water jet strikes a stationary inclined plate, it breaks into two…

A: if you have any doubts please comment

Q: In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target…

Q: Problem 1. Air flows steadily in a duct from Section (1) to Section (2). At Section (1), the…

Q: Water steam is running through the nozzle. Inlet pressure is P1=25 bars; T1=300C; V1=90m/s;…

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per…

A: Given data Industrial tank discharges water through a 5 inch nozzle at 5 m/s Diameter of nozzle = 5…

Q: 4. Determine the pressure required, in psi, in the pipe just ahead of the nozzle shown in the figure…

A: Given jet velocity v2= 75 fps diameter d1= 1 in diameter d2 = 0.75 in

Q: Do the ODE of it

A: Given: Radical flow turbine Absolute velocity at inlet = V1 Outer radius at inlet = l1 inner radius…

Q: Problem 5.2 A simple air duct with a side exhaust is shown below along with the direction of the…

A: (a) Write the given data. Cross-section areas,Ac1=Ac3=0.5 m2A2=0.5 m2Velocities,V1=10 m/sV3=3 m/s

Q: For the system shown below, calculate the vertical distance (in meters) between the surfaces of the…

Q: A 1.5-in-diameter water jet with a velocity of 100 fps impinges on a single vane moving in the same…

A: From the given data:

Q: A 75-mm diameter orifice discharges 23.41 L/s of liquid under a head of 2.85 m. The diameter of the…

A: To find : The three orifice coefficients. Given : The diameter of orifice is do=75 mm. The…

Q: The airduct shown below has a slanted exit, the dimension of which is 2 inch by 3 inch. Air is…

A: To obtain the solution to the above question, we must apply the ideal gas equation, which is as…

Q: Problem 2. An engineer helps with the design of a rotating spray for a dishwasher. The spray has 4…

Q: An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per…

A: Given:d=5 inv=5 m/sQin=225 US Gal/mint=15 minD=10 ftH=20 ft

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Problem 3. Momentum Equations.
This "double" nozzle discharges water at 10°C, (Ph2o = 1000 ) into the atmosphere at a rate of 0.50
m^3 /s. If the nozzle is lying in a horizontal plane, what x-component of force acting through the flange
in each jet to be the same. Jet A is
bolts is required to hold the nozzle in place? Note: Assume irrotational flow, and assume the water speed
12 cm in diameter, jet B is
20 cm in diameter, and the
pipe is
31 cm in diameter.
30
Figure 3. Problem 3 Illustration.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 14.2 A jet of water (r = 1000 kg/m³) is deflected by a vane mounted on a cart. The water jet has a constant cross-sectional area, A = 50 cm², which is projected off the vane at an angle q = 30° with respect to the horizontal. The pressure everywhere within the jet is atmospheric. The incoming jet velocity (with respect to the ground) is Vjet = 4.5 m/s. The cart has mass 50kg. Determine: a. the forces, Fx and Fy required to hold the cart stationary Vjet Vcart Fy Fx b. the horizontal force component, Fx, if the cart moves to the right at the constant velocity, Vcart = 3 m/s c. the horizontal acceleration of the cart at the instant when the cart moves with velocity Vcart = 2.5 m/s if no horizontal forces are applied Ans: a) 10 N
Given: Asked: Solution:
3. Air is flowing down a circular duct as shown in the figure. At station 1 the velocity is V₁ and the duct diameter is D₁. The duct gradually enlarges to station 2, where the air exits to the atmosphere, and the diameter is D₂. A conical centerbody with a cone angle of 30° is inserted into the duct exit. The diameter of the cone base is d. You may assume that the velocity is low enough that p = constant. control surface V₂ 1 0 = 30° V₂ F Figure for problem 3. (a) Find an expression for the gauge pressure at station 1 in terms of V₁, D₁, D₂, d, e, and p. What assumptions do you have to make to solve this problem? (b) What is the force, F, required to hold the cone in place? You may ignore the weight of the cone. Use the following values: V₁ = 20 m/s, D₁ = 30 cm, D₂ = 60 cm, and d = 58 cm. You may assume that the air density is at standard conditions, p = 1.225 kg/m².
Question Water enters the horizontal circular nozzle with the inlet diameter of 5 in. At the inlet section, fluid has uniformly distributed velocity of 20 ft/s and pressure of 85 psi. The water exits from the nozzle into the atmosphere at the outlet section where the uniformly distributed velocity is 100 ft/s. Determine the axial component of the anchoring force required to hold the contraction in place. Answer The axial component of the anchoring force required to hold the contraction in place is lbf.
The pump shown in the figure below produces a steady flow of 12 gal/s through the nozzle. Determine the nozzle exit diameter, D2, if the exit velocity is to be V₂ = 109 ft/s. D₂ = Pump i Section (1) Section (2) V₂ in
A lawn sprinkler can be used as a simple turbine. As shownin Fig. , flow enters normal to the paper in the centerand splits evenly into Q/2 and Vrel leaving each nozzle. Thearms rotate at angular velocity ω and do work on a shaft.Draw the velocity diagram for this turbine. Neglecting friction,find an expression for the power delivered to the shaft.Find the rotation rate for which the power is a maximum.
Calculate the power output from the turbine if the turbine efficiency is 75% and velocity at the nozzle 3 m/s and diameter of nozzle 50mm. EL=50m EL=30m D=50mm T D=100mm D=100mm
A high-pressure washing system's pump supplies 1 gallon of water persecond at 100 psi pressure. The nozzle should be designed so that the static pressureof the water as it exits the nozzle is the same as the atmospheric pressure. If theinside diameter of the hose leading from the pump to the nozzle is 2 in., whatshould the diameter of the nozzle exit be? What will be the velocity of the waterat the exit of the nozzle?
As seen in the figure above, the water is directed downward in the installation with a 25 ° narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Calculate (a) the effective pressure at point 2 (b) the x and y components of the force required to hold the elbow in place and the resultant force in the case where the flow is frictionless and gravitational effects are neglected. (pwater=1000 kg/m3, g=9.81m/s2)
3.
Water steam is running through the nozzle. Inlet pressure is P1=25 bars; T1=300C; V1=90m/s; A1=0.2m2. The exit parameters are: P2=11bars; T2=210C. The mass flow rate is m=2 kg/s. Determine: a.Exit velocity V2=?; b.Inlet and outlet diameters D1 and D2.
| The cross-sectional area is 25 square centimeter of water jet under the velocity of 35 meter per second and strikes tangentially a curved plate. The curvature angle of plate at the outlet is 120° with the x-axis. Find the force exerted by the get on the plate in the direction motion. Solve the problem, when the case of the plate is stationary and plate is moving in the direction of jet with the velocity of 15 meter per second.