Thermodynamics deals with the properties of the system relating work, heat transfer and internal energy system of the system. In a closed system 150 kJ of work is supplied. If the initial volume is 0.6 m3 and pressure of the system changes as per the law p = 8 – 4V, where ‘p’ is in bar, ‘V’ is in m3. Calculate the final volume and pressure of the closed system ?

Q: A piston cylinder device contains 500 g saturated water vapor at 125 kPa. The process is such that…

A: Given: PV2.394=constant Amount of water is 500 g (0.5 kg) P1 is 125 kPa P2 is 300 kPa Assume initial…

Q: Determine which of the following are true or false and explain your answer: a) In an adiabatic…

A: First statement is false In an adiabatic steady flow (single stream) process, the specific entropy…

Q: Consider an ideal gas which is being throttled to pressure of 1 bar at a rate of 100 mol/s The…

A: Molar flow rate of an idea gas = 100 mol/sInitial pressure = 25 barFinal pressure (pressure at the…

Q: exit velocity and what is the cross-sectional area at the nozzle exit f

A:

Q: Water at 45C and 10kPa enters an adiabatic pump and is discharged at a pressure of 8600 kPa.The pump…

A: Notations used, ‘1’ for inlet properties fluid and ‘2’ for exit one. The following assumptions are…

Q: Consider an ideal gas which is being throttled to a pressure of 1 bar at a rate of 100 mol/s…

A: Molar flow rate of an idea gas = 100 mol/sInitial pressure = 25 barFinal pressure (pressure at the…

Q: A quantity of ideal gas in an isolated system is expanded isothermally and reversibly at 500K.…

A: GIven that T =500 KQ =300 joules

Q: 100 g of F gas is stored in a cylinder in equilibrium with an external pressure of 1 atm and…

A: Given: Mass of the gas, m = 100 g Pressure, P = 1 atm = 101325 Pa Temperature, T = 305 K Exothermic…

Q: When the system is completely isolated from its surroundings so that there is no heat transfer, this…

A:

Q: Methane gas is compressed at the rate of 3x104 m3/hr (as measured at 0.1013MPa and 15°C) from…

A: Given data: The volumetric flow rate of the methane gas = 3×104 m3/h The methane gas is measured at…

Q: 7.1. Air expands adiabatically through a nozzle from a negligible initial velocity to a final…

A: Giveninitial velocity u1 = 0Final velocity u2 = 325 m/sto find = temp drop

Q: and

A: Given: System is at Equilibrium at 3 bar abs V = 5 m3 and 99 % (v/v) & 1 % Water (v/v) Weight…

Q: A steam turbine, operating reversibly and adiabatically, takes superheated steam at 2000 kPa and…

A: Given data: Pressure at the inlet of turbine = 2000 kPa Pressure at the exit of turbine = 50 kPa

Q: 3. In a constant reversible process, heat is added to 3 kg. of an ideal gas (k = 1.4, Cv 1.3 kJ/kg…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: 100 kg/s of superheated steam at 653.15 K and 8800 kPa enters a turbine and leaves as saturated…

A: Note: Since we are entitled to answer only 3 sub-parts, we will the first three. Please re-submit…

Q: Q3. A steam turbine operates adiabatically at a power level of 3000 kW. Steam enters the turbine at…

A: Consider a steam turbine operating at 3000 kW power level. Steam enters at 2100 kPa and leaves as…

Q: Propane gas is to be compressed irreversibly from 5 bar and 323 K to 15 bar and 343 K in an…

A: Given, The initial pressure of propane gas, P1 = 5 bar The initial temperature of the gas, T1 = 323…

Q: A piston cylinder device contains helium gas has initial pressure 180 KPa and initial temperature 25…

A:

Q: Air enters a compressor operating at steady state at 1.05 bar, 300 K, with a volumetric flow rate of…

A:

Q: Three sub steps of a thermodynamic cycle are employed in order to change the state of a gas from 1…

A: As given  1 step PV is constant  Internal energy U1 = 512 KJ U2 = 690KJ

Q: A methane gas, considered to be an ideal gas, initially at 750 K and 8 bar undergoes a process that…

A: Temperature T1 = 750k  Temperature T2 = 350k Pressure P1 = 8bar = 8*105Pa Preassure P2 = 1atm=…

Q: ca gas Wi 2. Steam at 2500 kPa and 350° C enters a turbine and leaves at 10 kPa. The turbine…

A:

Q: Q5: A cylinder piston contains 100/ air at 110 kPa. The air is then compressed in a reversible…

A:

Q: a. On the phase diagram, label the gas and liquid regions. b. Graphite is the most stable phase of…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: (1) Ten moles of methane at 300 K is compressed isothermally from 1 bar to 5 bar. The heat is…

A: The process is an isothermal process. The entropy change for an isothermal process is obtained from…

Q: 6.83. An equimolar mixture of methane and propane is discharged from a compressor at 5500 kPa and…

A: Introduction:- To raise a fluid's pressure, compressors are employed. The most common type of…

Q: Compressed air at room temperature (295 K) is contained in a 20-L tank at 2 bar. The valve is opened…

A:

Q: A generator does work on an electric heater by forcing an electric current through it. Suppose 1 kJ…

A: The change in the internal energy of the heater is to be determined.

Q: Find the entropy change of an ideal gas undergoing an isothermal process from 2.00 atm to 0.60 atm…

A: Given data:- Isothermal process P1 = 2 atm P2 = 0.60 atm Find the entropy change of an ideal gas.

Q: Air enters an adiabatic turbine at 600 kPa and 1000oC. The exit pressure of the air is 50 kPa.…

A: The temperature at the exit of the adiabatic turbine is to be calculated along with the amount of…

Q: Steam enters a turbine with a pressure of 20 bar, a temperature of 300 ℃, and a velocity of 200m/s.…

A: Draw the diagram for the turbine as follows:

Q: 8.6. A steam power plant employs two adiabatic turbines in series. Steam enters the first turbine at…

A: The initial temperature of the steam, T1 = 650 °C The initial pressure of the steam, P1 = 7000 kPa…

Q: Consider an ideal gas which is being throttled to a pressure of 1 bar at a rate of 100 mol/s The…

A: An ideal gas Throttled toP1=25 barP2=1 barRate ,r=100mol/sTs=300KFindRate of entropy generation,Lost…

Q: A rigid vessel of 0.06 m³ volume contains an ideal gas, CV = (5/2)R, at 500 K and 1 bar. a. If heat…

A:

Q: For the given question and solution, for part (b), finding the work input  of the saturated vapour…

A: A compressor is used to compress steam at two different phase of steam.

Q: Steam enters the turbine of a power plant operating on the Rankine cycle at 873.15 K and exhausts at…

A:

Q: Isobutane expands adiabatically in a turbine from 5000 kPa and 250°C to 500 kPa at the rate of 0.7…

A: Givenadiabatic expansion of isobutane  in a turbine from 5000 kPa and 250°C to 500 kPa flow rate of…

Q: 4. Steam enters a throttling valve (i.e. Joule-Thomson expansion) at 350 °C and 2 MPa, and leaves…

A: Steam inlet temperature = 350oCSteam inlet pressure = 2 MPaSteam outlet temperature = 300oCSteam…

Q: 3: A ges contained in a cylinder is compressed from 1 MPa and 0.05 m² to 2 MPa. Compression is…

A:

Q: Thermodynamics deals with the properties of the system relating work, heat transfer and internal…

A:

Q: Q1: Steam flows through a device with a stagnation pressure of 900kpa, a stagnation temperature of…

A: Given: Stagnation pressure P0= 900 kpa Stagnation temperature T0= 371 °C Velocity= 275 m/s, Cp=…

Q: Air is compressed steadily by a 5-kW compressor from 100 kPa and 17°C to 600 kPa and 167°C at a rate…

A: Given-details of air compression process and physical characteristics of the process To find-rate of…

Q: Steam enters an adiabatic turbine at 50 bar, 5000C and, after a stationary process, with steady…

A:

Q: 1.Steam enters an adiabatic turbine at 4MPA and 600C and exits at 40 kPa. If the efficiency of the…

A: