There is a nickel coating process. The area of materials 2.5 dm2, is coating by current flow is 75 minutes. The current is kept constant as 1.25 A (I), and the efficiency of current 95%. Calculate the thickness of coating. Atomic weight of nickel = 58.7 gr/mol Density of nickel = 8.9 g/cm3

Q: What is the formula for crushing efficiency, given specific surface area of a product, mass…

A:

Q: Discuss the following:1. The similarities and dissimilarities between wet scrubbing process and gas…

A: Wet gas scrubbers are devices that are used to remove a variety of pollutants from exhaust gas from…

Q: A square polymer sample of edge length 80 mm is subjected to a force of 6400 N. The resulting stress…

A: Given data: Length of edge of a square = 80 mm Force = 6400 N

Q: A 10mm diameter tungsten cylindrical bar should fit a 9.988mm hole contained in a steel plate.…

A:

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: For heat transfer, the surface resistance was characterized by a convective heat transfer…

A: For convective heat transfer the heat transfer quotient h is given by:

Q: If the temperature profile in a rectangular slag is represented by: T(x,y,z)=x2-2y2+z²-xy+2yz…

A: The points where spacial derivatives wrt to time are 0 will be where Temperature won't change. We…

Q: Make a comparison between thermoplastics and thermosetting polymers(a) on the basis of mechanical…

A: A resin that is solid at room temperature but becomes plastic and soft upon heating is a…

Q: Why do some evaporators operate under vacuum? How is the vacuum produced?

A: The reason for operation of some evaporators under vacuum is to be mentioned along with the method…

Q: Explain why: a) A metallic couple with an unfavourable area ratio (small anode/large cathode)…

A: The given subparts need to be explained.

Q: The heat is propagating through a stainless steel wall with thermal diffusivity of 6x10^(-6)m2/s. If…

A: Given that- Heat is propagating through a stainless steel wall. Thickness of wall, l=52.00 mm=0.052…

Q: Determine the Cunningham Correction Factor for the following particles at 400K and standard pressure…

A:

Q: In the Energy and Specific Heat lab, how should the aluminum can be stabilized over the heat source?…

A:

Q: A polished stainless steel surface is electrically heated form the bottom to boil water at…

A: Material = Polished stainless steelPressure, Temperature,

Q: What is the thermal Diffusivity. Write down the factors effecting it.

A: Thermal Diffusivity Thermal Diffusivity is defined as the ratio of heat conducted to heat stored.…

Q: 5. Physical properties of the formation crude oil includes volume coefficient and viscosity.

A: The physical properties of crude oil vary according to its composition, the relative abundance of…

Q: er coefficient, overall heat transfer coefficient based on the outside surface and the rate of…

A: Fig 1: Spherical storage tank

Q: Water at 150 °C flows on the inside of a 1 meter long 2" Schedule 80 steel pipe (thermal…

A: Dear User, Kindly note that according to bartleby policy, we can answer only 3 subparts from the…

Q: On Mars, people live in domes. The outside of the dome walls are made of aluminium. However, the…

A:

Q: 6. Which ratio of cathode to anode accelerates galvanic corrosion? a. Larger cathode to smaller…

A: In general, the rate of corrosion is significantly impacted by the relative sizes of the cathodic…

Q: The condensing vapour is usually placed side of Shell and tube heat exchanger.

A: Given: Condensing vapor is placed in which side of STHE?

Q: Steel is an example of  __________.   A. interstitial alloy   B. ionic solid   C. molecular solid…

A: We can say steel is an example of an interstitial alloy, due to the very small carbon atoms fit into…

Q: On which factors do the heat gain in a CSTR depends?

A: CSTR refers to a continuous stirred tank reactor and in Chemical engineering it is used to model…

Q: 3. A 650 Bhp diesel engine uses fuel oil of 28 API gravity. Fuel consumption is 0.65lb/Bhp- hr. Cost…

A: First, calculating the specific gravity of the fuel oil of 28 API gravity as follows: SGat 15.6oC =…

Q: Determine the following for each item: 1. Equivalent surface diameter 2. Equivalent volume diameter…

A: (1) Equivalent surface diameter is defined as the diameter of the sphere having equal surface area…

Q: Bitumen 60/7O Pen is more preferred in hot climate region compared to 30/40 Pen bitumen.

A: Bitumen penetration grade 60/70 means the penetration value is in the range 60 to 70 at standard…

Q: List three types of annealing used in thermal processing of metals, and describe ONE in detail.

A: according to Bartleby's guidelines, I can only solve one question at a time 3) three types of…

Q: Given the table below and your judgement for extreme operational conditions, select polymers for the…

A: Given Data Different Material With their Glass Transition Temperature and Melting Point.  To find…

Q: Q3: A 1-mm-thick copper plate (k 386 W/m C) is sandwiched between two 2-mm-thick epoxy boards (k…

A: Given data are as shown below:K = 386 W/m*c for copper plateK = 0.26 W/m*c for epoxy boardsarea =…

Q: v Abrasive A. Fireclay v High thermal shock resistance B. Whiteware clay ceramic v Washbasin C.…

A: To match entries in the left column with those in right column

Q: Effect of the carbon percentage on the shape and magnitude (mechanical properties) of stress-strain…

A:

Q: 6-Calculate the overall heat transfer coefficient based on the inner diameter for a steel pipe…

A: Given, The inner diameter of the pipe, di = 20 mm The thickness of the pipe, δs = 2 mm The thickness…

Q: a)Determine the Reynolds, Schmidt, and Sherwood numbers associated with this process.  b) What is…

A:

Q: Discuss the Water Sachet Failure due to Change in Supplier and one thermal analysis technique for…

A: Introduction Potable sachet water (drinking water)  quality is solemnly dependent on the quality of…

Q: 3-Find the total thermal resistance from the series and parallel compo=

A: It is required to calculate the total thermal resistance from the series and parallel composite wall

Q: mm diameter glass tube is inserted into an open glass of water (contact angle between the tube and…

A:

Q: Describe with neat diagrams various types of commercial evaporators. Discuss the important features…

A: Evaporators  Evaporators heat exchange systems used for concentration , dewatering and…

Q: Did you lose a process called chemical vapor disposition to pleat platinum into the surface of…

A: The time required by the jeweler to make a coating of the thick silver on the available surface of…