There are two square columns of equal length and of same material. First has both ends hinged while the second has both ends fixed. If both the columns need to have equal buckling load, the size of the first column is times the size of the second column.

There are two square columns of equal length and of same material. First has both ends hinged while the second has both ends fixed. If both the columns need to have equal buckling load, the size of the first column is times the size of the second column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
DON'T ANSWER IF YOU ALREADY ANSWERED THIS. IF YOU ANSWER THIS CORRECTLY I WILL LIKE LIKE YOUR ANSWER. THANK YOU
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
I need the answer as soon as possible
please use only set 1 data table thank you this is non graded
If beam BEH is hinged at the columns B, E, and H, determine its degree of indeterminacy.
An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECIGON CIVIL ENGINEERING Beam properties: A= 11,500 mm² bf = 250 mm tw- 10 mm d === 350 mm If=: 16 mm 1x = 266 x 106 mm c) To strengthen the beam, 2- 200 mm x 10 mm cover plates, one at the top of the flange and the other at the bottom of the flange were added. What is the resulting maximum bending stress?
Determine the bar forces of member BG. For the given loads: X= 26 kN, Y= 78 kN, Z= 104 kN, B= 26 Y G H. A m B C D E Y 4 @ 3B m = 12B m 6B m
Question 29 The laminated beam, shown in cross section, is composed of ?ve 6- in. by 2-in. planks that are glued together. The beam carries a uniformly distributed load of intensity we over its 8-ft simply supported span. If the working stresses are 75 psi for shear in glue, 90 psi for shear in wood, and 8ø0 psi for bending in wood, + 6 in. 1. determine the maximum allowable value of we so that the shear stress in the wood is not exceeded. A. 900 lb/ft C. 833 lb/ft determine the maximum allowable value of we so that the shear B. 555 lb/ft D. NOTA 2. stress in the glue is not exceeded. A. 900 lb/ft C. 833 lb/ft B. 555 lb/ft D. NOTA 3. determine the maximum allowable value of we so that the bending stress in the wood is not exceeded. А. 900 lb/ft В. 555 lb/ft C. 833 lb/ft D. NOTA 5 @ 2 in. = 10 in. –
-This Engineering Mechanics - Static of Rigid Bodies : Method of Sections - [ ] Solution must include FBDs #4
please help
The floor structural system shown in Fig 1 comprise W-section steel beams and girders supporting a 5-inch thick concrete slab which provides full restraint to the flanges of the beams. The density of concrete is 150 lbs. /ft³. and the uniformly distributed live load L=50 lbs/ft². L-22¹ B B. Girder G1: - [82] 12' Gl GI [BI] FIG. 1-Steel Floor Beam a) Strength - Bending and Shear 12' + I 1) Produce a sketch of the floor plan showing the tributary load distribution areas for the beams and girders [zul