A uniform light slender beam AB of section modulus EI is pinned by a frictionless joint A to the ground and supported by a light inextensible cable CB to hang a weight W as shown. If the maximum value of W to avoid buckling of the beam AB is obtained as ßn²EI, where is the ratio of circumference to diameter of a circle, then the value of ß is 來 A 2.5 m 30° g B W

A uniform light slender beam AB of section modulus EI is pinned by a frictionless joint A to the ground and supported by a light inextensible cable CB to hang a weight W as shown. If the maximum value of W to avoid buckling of the beam AB is obtained as ßn²EI, where is the ratio of circumference to diameter of a circle, then the value of ß is 來 A 2.5 m 30° g B W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
Ggg
A beam ABC rests on simple supports at points A and B and is supported by a cable at point C. The beam has total length 2L and supports a uniform load of intensity q. Prior to the application of the uniform load, there is no force in the cable nor is there any slack in the cable. When the uniform load is applied, the beam deflects downward at point Cand a tensile force I develops in the cable. Find the magnitude of this force. Cable A T A B C 000
A continuous beam supports loads as shown in the image. Determine the support reactions using the three-moment method. Consider that the stiffness of the beam is constant throughout.
The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical. Positive values are to the right, up, and counterclockwise.
I need the answer as soon as possible
find the reactions at each support for the truss shown. there may be mutliple answers for each support. neglect the weight of the truss.
a. The reactions at the support for a simple beam loaded as shown. Neglect the weight of the beam. b. The internal forces at point C. A 225 N-m 0.125 m с 0.125 m 450 N 0.125 m 700 N 0.125 m B
Q2. Figure Q2 shows the free body diagram of a 10 m long beam AD of uniform cross-section, simply supported at locations A and C. A uniformly distributed load of 10 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end D. 10kN/m 20kN AV B 4m 4m 2m Fig.Q2: Structural Beam (d) From the SFD drawn in (b), find the distance from point A to the position between points A and B where there is no shear and determine the bending moment at that position. (e) Write the mathematical expression for shear force Vat section X-X between the points B and C which is at distance x measured from support А.
1.2 p kN q kN/ m L = 14 m d = 4 m q = 100 kN/m p = 50 kN A В A Simply supported beam is Lm long and is subjected to a uniformly distributed load of q ķN/m applied for the full length of the beam and a concentrated load of p kN of the beam as shown. Draw the free body diagram of the given beam and find the support reactions.
Cantilever beam is loaded by two concentrated forces and a couple. F2 M 4 4 1, Given: 11= 13cm; l 2 = 28cm; 13 = 19cm; F1 = 283N; F 2 = -54N; M= -7N m. Find: algebraical value of reactive moment (in N m) applied at fixed point (considering counterclockwise direction as positive and clockwise as negative). Answer:
The system shown is made up of an ABG bar, supported by a pin at point A and by a smooth collar al point B (the collar slides in the ABG bar) the collar is pinned to rod BDE and the rod BDE is supported by a pin at D and a cable at end E. Based on the above determine: a) The load P, such that the cable force is T=20 lb. b) The internal loads in a section passing through point G (normal and shear force, bending moment) c) Drawn bar BDE horizontally and generate a shear force and bending moment diagrams. Indicate the maximum values of the shear force and bending moment and their location The value of a=7 in and b= 6 in P G A 11 in, 40° B 7 in D 4 in E F