Please compute for g, h, and i. Thank you 1. The working substance for a Carnot cycle is 8 lb of air.The volume at the beginning of isothermal expansion is 9 cu ftand the pressure is 300 psia. The ratio of expansion during theaddition of heat is 2 and the temperature of the cold body is90°F. Find (a) Q, (b) Qg, (c) Va, (d) p, (e) V,, (f) p,, (g) p, (h) theratio of expansion during the isentropic process, and (i) theoverall ratio of compression.Ans.(a) 346.4 Btu; (b) -209.1 Btu; (c) 63.57 cu ft; (d)25.64 psia; (e)31.79 cu ft; (f) 51.28 psia; (g) 13.59 psia; (h) 3.53;(8) 7.06

m=8lbv1=9ft3P1=300Psi=300×144lbt/ft2 2feet =12inchv2v1=2 v2=2v1=18ft3T3=T4=90°f=305.37kfor process…

The working substance for a Càrnot eycle plume at the beginning of isothermal expansion is 9 cu ft ne pressure is 300 psia. The ratio of expansion during the on of heat is 2 and the temperature of the cold body is Find (a) Q, (b) Qg, (c) V, (d) p3, (e) V, (f) P, (g) p.m (h) the of expansion during the isentropic process, and (i) the Il ratio of compression. Ans. (a) 346.4 Btu; (b) -209.1 Btu; (c) 63.57 cu ft; (d)

The working substance for a Càrnot eycle plume at the beginning of isothermal expansion is 9 cu ft ne pressure is 300 psia. The ratio of expansion during the on of heat is 2 and the temperature of the cold body is Find (a) Q, (b) Qg, (c) V, (d) p3, (e) V, (f) P, (g) p.m (h) the of expansion during the isentropic process, and (i) the Il ratio of compression. Ans. (a) 346.4 Btu; (b) -209.1 Btu; (c) 63.57 cu ft; (d)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLS SHOW COMPLETE SOLUTION. SOLVE IT BY HANDWRITTEN. ANSWERS SHOULD BE ROUND OFF TO FOUR SIGNIFICANT FIGURES.
All problems will use the conventional Cartesian coordinate system unless noted otherwise. Positive x-axis points to the right, Positive y-axis points up, Angles are measured CCW (counter-clock-wise) from the positive x-axis. Problem-BB: Consider FIG-BB in the appendix. AC is a rope. BC is a rope. “C” is a steel ring. “D” is a perfect pulley. A continuous rope connects “C” to the mass. Calculate the internal forces within each rope.
15-1. A 100-ft grid is located over an area that measures 800 ft in the north-south direction and 800 ft in the east-west direction. The southwesterly corner is designated A-1 and the southeasterly corner is designated I-1. The northwesterly corner is designated A-9 and the northeasterly corner is designated I-9. Elevations are obtained at the grid points using a total station instrument, rounded off to the nearest foot. These are tabulated as follows: 375 372 366 360 354 350 340 322 302 312 365 364 8 372 372 370 368 362 361 339 7 366 365 365 366. 362 361 347 319 359 328 328 6. 363 353 350 360 362 350 347 361 340 335 343 352 350 338 334 4 360 344 329 328 337 339 325 321 321 3 360 343 320 317 318 318 313 312 312 308 302 303 323 326 2 358 343 316 310 303 291 340 B 1 353 318 310 303 297 292 A C D F G H Plot a grid to a scale of 1 in. = 200 ft and draw in 10-ft contour lines.
Determine the number of instant center and locate all of them using IC Circle method. You may use a software to visualize the motion of the linkage. With a Variable 0 = 45. Block 3 slides along link 2. Q1A = 12 inch, Q2D = 2 Linch, Q2C = 1 2 inch, BC = 3-inch, 8 16 AB = 2 inch, Q1Q2 = 2 2 inch 2 4 1 Q1 Q2 A B.
Please and thank
Q3: Write two G-code programs using the following figure where units are in inches. a. The first program should use absolute positioning, and b. the second program should use incremental positioning. P4 Finish (6, 4) P2 (1, 3) P3 (4.79, 2) P1 Start (-2, 1) Center (2.5, 1) -2
will Bou 5-5.16. For the cylinder described in Prob. 5-5.14, determine the minimum horizontal force P applied tangentially. to the left at the top that will start counterclockwise rotation.
Can you please solve for va and vb. This is not what I asked for
Q2: Write the G-code for the below geometry, use G90, explain all code steps. 30 30 40 R40 R30 DATUM 70 30 Start Point
Plz solve all parts hand written plz asap... I'll rate plz fast solve it within half n hour and hand written
I need the solution in hand writing