The wood pole is supported by two cables of 6 mm diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 136 MPa. If the working compressive stress for wood is 15 MPa, determine the smallest permissible diameter of the pole in millimeters

Q: The aluminum rod. cylindrical steel rod DE (E = 29×10 psi) of the same overall length. Determine the…

A:

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: given data;load=mg=25*9.81=245.25Nlimiting stress σ=27.24kpa=27240Pa=27240N/m2cross sectional…

Q: Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of…

A:

Q: The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force…

A:

Q: 25 kN 20 kN 30 kN 14 -1.5 m- 3 m 3 m

A:

Q: Bar (1) has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be limited to 39 ksi,…

A: Correct answer: (b) 17.55 kips

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

A:

Q: The wood pole is supported by two cables. The turnbuckles in the cables are tightened until the…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given data, Di = 100 mm. Tensile load = P = 400 KN = 400000 N. Stress= σ = 120 MN/ m2 = 120 N/mm2…

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: P= 189.3 kN= 189.3(1000) N= 189300 N Cross sectional area of the bronze, ABronze= 400 mm^2 Magnitude…

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

A:

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

A: givend1=18mmd2=31mm

Q: A hollow steel tube with an inside diameter of 100mm must carry a tensile load of 400 kN. Determine…

A: We have to determine hollow steel diameter

Q: Required information Rod BD is made of steel (E = 29 x 106 psi) and is used to brace the axially…

A: According to the given dataE=29x106psiP=106 kipsFBD=0.014PΔlBD = 0.0009ACWe need to find Diameter…

Q: hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given, the tensile load, P=400kN=400000N Stress, σ=120MPa Area, A=14πD2-14π1002=14πD2-10000

Q: Bar (1) has a cross-sectional area of 0.75 in.2. If the stress in bar (1) must be limited to 49 ksi,…

A: Correct answer: (iv) 22.05 kips

Q: A short post constructed from a hollow circular tube of aluminum supports a compressive load of P =…

A:

Q: Determine the maximum stress in the frame of the 100 kN punch press as shown in Fig. 8.13. 100kN…

A: As illustrated in the diagram, we must calculate the maximum stress in the frame of the 100 kN punch…

Q: eter of wires AB and CB. The allowable tensile stress in each wire is 185 Mpa. 30

A:

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ   Required : Force

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A: Given Data The load acting at A is PA=80 kN. The load acting at B is PB=280 kN.  The ultimate…

Q: Given the section is subjected to a moment of 500 N-m, calculate the normal stress in MPa at the…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is O₂ = 840 psi,…

A: Answer: Pmax = 11600 lb

Q: Rod BD is made of steel (E= 29 × 100 psi) and is used to brace the axially compressed member ABC.…

A:

Q: A cantilever beam, 80 mm wide by 270O mm high and 8 m long, carries a load that varies uniformly…

A: Draw a diagram for the cantilever beam. Here, w1 is the load intensity at point B i.e. at 5 m from…

Q: A cantilever beam, 100 mm wide by 230 mm high and 7 m long, carries a load that varies uniformly…

A: Due to bending in a beam , there are two types of stresses acting in a beam which are- 1. Bending…

Q: The joint is subjected to the axial member force of 6 kips. Determine the average normal stress…

A:

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A:

Q: lamp=81kg, AB=5mm, BC=8mm

A:

Q: 04 It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN)…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.