The wires of our appliances areinsulated with a material mixed withrubber, which has a very high resistivity.If a certain wire has a length of 2.5m,the outer diameter is 5mm and its innerdiameter is0.5mm, whatthatis itstheresistance?diameter is present to leave a hollowplace where the conducting wire(usually copper) is present.NoteinnerSelf-PacedPracticeProblem 7.2

Answered: Image /qna-images/answer/c060191d-5f3b-4203-bb11-4b516dc1b1ba.jpg

The wires of our appliances insulated with a material mixed with are rubber, which has a very high resistivity. If a certain wire has a length of 2.5m, the outer diameter is 5mm and its inner what is diameter is 0.5mm, that its resistance? Note the inner d d diameter is present to leave a hollow place where the conducting wire (usually copper) is present. 72

The wires of our appliances insulated with a material mixed with are rubber, which has a very high resistivity. If a certain wire has a length of 2.5m, the outer diameter is 5mm and its inner what is diameter is 0.5mm, that its resistance? Note the inner d d diameter is present to leave a hollow place where the conducting wire (usually copper) is present. 72

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2 AWG Copper conductor is 450' long what is the resistance of the wire? assumed the ambient temp to be 20ﾟC
Requirements: 1. Fill the tables. 2. Calculate the thermal conductivity and the thermal resistance. Comment on results. 3. Plot the measured values for temperature difference over the electrical power. please don't reject the question. Thank you
An ideal capacitor with a capacitance of 90.0 nF is charged up to a voltage of 3.00 V. (i) Calculate the magnitude of charge stored in the capacitor. (ii) Determine the potential energy stored in the capacitor. (iii) The capacitor is disconnected from the battery and is then inserted with a piece of mica of which the dielectric constant is 5.00. Compare the final potential energy to the initial potential energy in the capacitor.
1. please write clean and as much detail as you can 2. please draw the FBD since I am not understanding the temperature placement on this question 3. to make your job easier the following formula apply : Q_cond=Q_conv+Q_radi KA(T_i-T_o )/L=hA(T_s-T_∞ )+ε σ A(T_s^4-T_∞^4 )
A single square loop of wire is placed in the center of a large solenoid as shown. The solenoid has a radius 5.00 cm and the square loop is 3.0 cm on a side. The solenoid is 0.20 cm long and wound with 200 turns of wire. If the current in the solenoid is 3.00 A, what is the flux through the square loop? If the current in the solenoid drops to zero in 0.500 seconds, what is the magnitude of the average induced emf in the square loop?
A large motor neuron runs from the brain to the arm. The neuron contains a core of bundled microtubules. If the motor neuron is 40 cm long, and the magnitude of the potential difference from the top of the neuron to the bottom is 40 mV, then what is a reasonable estimate for the magnitude of the cross sectional area of the neuron? Take the resistivity of the microtubule to be about 40 MO/um.
A charged nonconducting rod, with a length of 2.52 m and a cross-sectional area of 4.76 cm², lies along the positive side of an x axis with one end at the origin. The volume charge density p is charge per unit volume in coulombs per cubic meter. How many excess electrons are on the rod if p is (a) uniform, with a value of -4.66 µC/m³, and (b) nonuniform, with a value given by p= bx², where b = -2.18 µC/m²? (a) Number i (b) Number i Units Units
A thermionic generator with a cathode work function of 2.2 V and an anode work function of 1.6 V operates at a cathode temperature of 1400 K. For ideal values, assume zero retarding voltage in the interspace. (a) What should be the approximate anode temperature? (b) What would be the ideal current density? (c) Calculate the ideal power output per cm’ and the thprmal efficiency. Your answer
A wire carrying 0.50 A of current is place in a magnetic field with a strength of 0.75 T. The length of the wire is 41 cm. What is the magnitude of the magnetic force on the wire?
(a) A wire carrying a 20.5 A current passes between the poles of a strong magnet that is perpendicular to its field and experiences a 2.46 N force on the 3.75 cm of wire in the field. What is the average field strength? Average field strength in tesla = (b) A spherical surface of area 0.7m2, emissivity 0.85 and temperature 134°C is placed in a large, evacuated chamber whose walls are maintained at a fixed temperature. Find the rate at which radiation is emitted by the surface?( Stefan's constant σ = 5.67 x 10-8 W/m2T4 ) Energy radiated per second in watts =